My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
I have system which is using a lot of bandwidth and this is not a big problem,
but how do you troubleshoot this issue?
How can I find out which connections are made for one interface card,
there are about 5 on this system and I can see how much traffic is going through one interface, but I need... (5 Replies)
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Hi Experts,
I have an issue where the interface card went down for like four times in last one week in redhat linux server. Every time it goes down, it comes back.
2014 Oct 21 07:22:14 <hostname> kernel: nx_nic: NIC Link is down
2014 Oct 21 07:22:21 <hostname> kernel: nx_nic: NIC Link is... (3 Replies)
I'm looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A for Solaris. It used to be on sun-solve, but I fail to find it on the Oracle site. Any help would be very appreciated! (1 Reply)
Discussion started by: Ira28
1 Replies
LEARN ABOUT XFREE86
pccard
PCCARD(4) BSD Kernel Interfaces Manual PCCARD(4)NAME
pccard -- PC Card bus driver
SYNOPSIS
device pccard
DESCRIPTION
The pccard driver implements the PC Card bus. The pccard driver supports all PC Card bridges in the system.
TUNABLES
The driver supports the following tunable parameters, which may be added to /boot/loader.conf or set via the sysctl(8) command:
hw.pccard.debug Non-zero values cause more verbose information to be printed when a 16-bit PC Card is inserted or removed.
hw.pccard.cis_debug Non-zero value causes the CIS parsing of the 16-bit PC Card to be much more verbose and include a complete CIS dump.
FILES
/dev/pccard0.cis This exclusive-use device will report all the CIS chains present in a PC Card, if a 16-bit PC Card is inserted in the slot.
Only one user at a time may access the CIS. The CIS is presented as the relevant byte stream from the PC Card. For CIS
tuples in Attribute Memory (the default), only the even locations are presented (the ODD locations are undefined per the
standard). For CIS tuples in Common Memory, every byte is presented to the user. Decoding of the CIS tuples is done via a
userland program. All tuples are presented to the user.
SEE ALSO cardbus(4), pccbb(4)
PC Card Standard, Release 8.
BSD July 9, 2002 BSD