Sponsored Content
Operating Systems Linux Red Hat Regarding Network Interface Card Post 302919445 by gull04 on Wednesday 1st of October 2014 09:33:15 AM
Old 10-01-2014
Hi,

OK, some things to check.

First, ensure that the networking is properly set all the way from client to server. By that I mean,
  • All speeds must match - under no circumstances allow auto negotiation.
  • Everything should be full duplex all the way through.
  • Ensure that the "NET_BUFFER_SZ" variable matches your DB requirements.

A little by the way of explanation, all your network interfaces all the way through should be set to the same speed - for arguments sake - 100Mb Full Duplex - this includes switches.

There are a lot of available settings to configure the Client and the Server communications in Netbackup, also your version is later than the version I'm running here. I'm assuming that you will have support on a version as new as that. So I'd be tempted to check the Symantec site - the support there tends to be quite good.

Anyway, let me know how you get on.

Regards

Dave
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Multi Network card interface problem

My system info is show below:- #uname -a SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500 and I have two network card as shown below:- #ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies

2. Red Hat

How to configure network interface card in OEL.

Hi I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest. Thanks Ankur (2 Replies)
Discussion started by: ankurk
2 Replies

3. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

4. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies

5. Solaris

Interface card using a lot of bandwith

I have system which is using a lot of bandwidth and this is not a big problem, but how do you troubleshoot this issue? How can I find out which connections are made for one interface card, there are about 5 on this system and I can see how much traffic is going through one interface, but I need... (5 Replies)
Discussion started by: misterx12345
5 Replies

6. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

7. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

8. Red Hat

Interface card link goes down and recovers frequently

Hi Experts, I have an issue where the interface card went down for like four times in last one week in redhat linux server. Every time it goes down, it comes back. 2014 Oct 21 07:22:14 <hostname> kernel: nx_nic: NIC Link is down 2014 Oct 21 07:22:21 <hostname> kernel: nx_nic: NIC Link is... (3 Replies)
Discussion started by: dhanu1985
3 Replies

9. Solaris

Looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A

I'm looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A for Solaris. It used to be on sun-solve, but I fail to find it on the Oracle site. Any help would be very appreciated! (1 Reply)
Discussion started by: Ira28
1 Replies
TXP(4)							   BSD Kernel Interfaces Manual 						    TXP(4)

NAME
txp -- 3Com 3XP Typhoon/Sidewinder (3CR990) Ethernet interface SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file: device txp Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_txp_load="YES" DESCRIPTION
The txp interface provides access to the 10Mb/s and 100Mb/s Ethernet networks via the 3Com Typhoon/Sidewinder chipset. Basic Ethernet functions are provided as well as support for vlan(4) tag removal and insertion assistance, receive ip(4), tcp(4), and udp(4) checksum offloading, and transmit ip(4) checksum offloading. There is currently no support for transmit tcp(4) or udp(4) checksum offload- ing, tcp(4) segmentation, nor ipsec(4) acceleration. Each of the host's network addresses is specified at boot time with an SIOCSIFADDR ioctl(2). The txp interface employs the address resolu- tion protocol described in arp(4) to dynamically map between Internet and Ethernet addresses on the local network. When a txp interface is brought up, by default, it will attempt to auto-negotiate the link speed and duplex mode. The speeds, in order of attempt, are: 100Mb/s Full Duplex, 100Mb/s Half Duplex, 10 Mb/s Full Duplex, and 10 Mb/s Half Duplex. The txp supports several media types, which are selected via the ifconfig(8) command. The supported media types are: media autoselect Attempt to autoselect the media type (default) media 100baseTX mediaopt full-duplex Use 100baseTX, full duplex media 100baseTX [mediaopt half-duplex] Use 100baseTX, half duplex media 10baseT mediaopt full-duplex Use 10baseT, full duplex media 10baseT [mediaopt half-duplex] Use 10baseT, half duplex HARDWARE
The txp driver supports the following cards: o 3Com 3CR990-TX-95 o 3Com 3CR990-TX-97 o 3Com 3cR990B-TXM o 3Com 3CR990SVR95 o 3Com 3CR990SVR97 o 3Com 3cR990B-SRV SEE ALSO
altq(4), arp(4), inet(4), intro(4), ip(4), miibus(4), tcp(4), udp(4), vlan(4), ifconfig(8) HISTORY
The txp driver first appeared in OpenBSD 2.9. BSD
March 12, 2009 BSD
All times are GMT -4. The time now is 05:07 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy