10-01-2014
Hi,
This could be down to several things, firstly a couple of questions.
First, what version of Netbackup.
Second, was the error on the Client or the Server.
Third, how much data - I think in some older versions these type of errors were due to size.
Fourth, what is being backed up and how - is it NDMP etc.
The more information that you provide, the better the chance that someone will be able to assist you.
Regards
Dave
Last edited by gull04; 10-01-2014 at 06:55 AM..
Reason: Typo
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
2. Red Hat
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Discussion started by: ankurk
2 Replies
3. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
4. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
5. Solaris
I have system which is using a lot of bandwidth and this is not a big problem,
but how do you troubleshoot this issue?
How can I find out which connections are made for one interface card,
there are about 5 on this system and I can see how much traffic is going through one interface, but I need... (5 Replies)
Discussion started by: misterx12345
5 Replies
6. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
7. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
8. Red Hat
Hi Experts,
I have an issue where the interface card went down for like four times in last one week in redhat linux server. Every time it goes down, it comes back.
2014 Oct 21 07:22:14 <hostname> kernel: nx_nic: NIC Link is down
2014 Oct 21 07:22:21 <hostname> kernel: nx_nic: NIC Link is... (3 Replies)
Discussion started by: dhanu1985
3 Replies
9. Solaris
I'm looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A for Solaris. It used to be on sun-solve, but I fail to find it on the Oracle site. Any help would be very appreciated! (1 Reply)
Discussion started by: Ira28
1 Replies
LEARN ABOUT CENTOS
upgradedb
UPGRADEDB(8) System Manager's Manual UPGRADEDB(8)
NAME
upgradedb - Directory Server script for upgrading the database
SYNOPSIS
upgradedb [-a archivedir] [-Z serverID] [-f] [-v] [-d debuglevel] [-h]
DESCRIPTION
Checks the DB version and if it has the old index formatting then it will rebuild the indexes. This is usually needed after migrating from
older versions of Directory Server. This script must be run while the server is stopped.
OPTIONS
A summary of options is included below:
-n Backend Name
The name of the LDBM database to reindex. Example: userRoot
-a Database directory
The full path to the database directory.
-Z Server Identifier
The server ID of the Directory Server instance. If there is only one instance on the system, this option can be skipped.
-N Only checks whether any DNs in the database need to be updated.
-h
Display the usage.
EXAMPLE
upgradedb -Z instance2
DIAGNOSTICS
Exit status is zero if no errors occur. Errors result in a non-zero exit status and a diagnostic message being written to standard error.
AUTHOR
upgradedb was written by the 389 Project.
REPORTING BUGS
Report bugs to http://bugzilla.redhat.com.
COPYRIGHT
Copyright (C) 2013 Red Hat, Inc.
Mar 5, 2013 UPGRADEDB(8)