Regarding Network Interface Card Post: 302919402

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Multi Network card interface problem

My system info is show below:- #uname -a SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500 and I have two network card as shown below:- #ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0:...

2. Red Hat

How to configure network interface card in OEL.

Hi I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest. Thanks Ankur

3. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

4. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

5. Solaris

Interface card using a lot of bandwith

I have system which is using a lot of bandwidth and this is not a big problem, but how do you troubleshoot this issue? How can I find out which connections are made for one interface card, there are about 5 on this system and I can see how much traffic is going through one interface, but I need...

6. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

7. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

8. Red Hat

Interface card link goes down and recovers frequently

Hi Experts, I have an issue where the interface card went down for like four times in last one week in redhat linux server. Every time it goes down, it comes back. 2014 Oct 21 07:22:14 <hostname> kernel: nx_nic: NIC Link is down 2014 Oct 21 07:22:21 <hostname> kernel: nx_nic: NIC Link is...

9. Solaris

Looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A

I'm looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A for Solaris. It used to be on sun-solve, but I fail to find it on the Oracle site. Any help would be very appreciated!

LEARN ABOUT SUSE

beid-pkcs11-tool

beid-pkcs11-tool(1)						      Belgium						       beid-pkcs11-tool(1)

NAME

       beid-pkcs11-tool - generic smart card utility

SYNOPSIS

       beid-pkcs11-tool [OPTIONS]

DESCRIPTION

       The  beid-pkcs11-tool utility can be used from the command line to perform miscellaneous operations on the Belgium eID PKCS11 library, such
       as changing your PIN or testing the library.

OPTIONS

       --show-info, -I
	      Show global token information

       --list-slots, -L
	      List the available slots

       --list-mechanisms, -M
	      List the mechanisms supported by the token

       --list-objects, -O
	      List the objects on the token

       --login, -l
	      Log into the token first (not needed when using --pin)

       --pin pin, -r pin
	      Supply the PIN on the command line

       --change-pin, -c
	      Change the PIN

       --slot slot
	      Specify number of the slot to use

       --module module
	      Specify PKCS11 library to use (default = libbeidpkcs11.so)

       --test, -t
	      Test (best used with the --login or --pin option)

SEE ALSO

       beid-tool(1)

AUTHORS

       beid-pkcs11-tool is based on pkcs11-tool (www.openc.org) and adapted for the Belgian national eID card by Zetes NV/SA (www.zetes.com).

								      09/2005						       beid-pkcs11-tool(1)