10-01-2014
Hi jegaraman,
What backup tool are you using?
Regards
Dave
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
2. Red Hat
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Discussion started by: ankurk
2 Replies
3. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
4. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
5. Solaris
I have system which is using a lot of bandwidth and this is not a big problem,
but how do you troubleshoot this issue?
How can I find out which connections are made for one interface card,
there are about 5 on this system and I can see how much traffic is going through one interface, but I need... (5 Replies)
Discussion started by: misterx12345
5 Replies
6. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
7. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
8. Red Hat
Hi Experts,
I have an issue where the interface card went down for like four times in last one week in redhat linux server. Every time it goes down, it comes back.
2014 Oct 21 07:22:14 <hostname> kernel: nx_nic: NIC Link is down
2014 Oct 21 07:22:21 <hostname> kernel: nx_nic: NIC Link is... (3 Replies)
Discussion started by: dhanu1985
3 Replies
9. Solaris
I'm looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A for Solaris. It used to be on sun-solve, but I fail to find it on the Oracle site. Any help would be very appreciated! (1 Reply)
Discussion started by: Ira28
1 Replies
LEARN ABOUT DEBIAN
svn-fast-backup
svn-fast-backup(1) General Commands Manual svn-fast-backup(1)
NAME
svn-fast-backup - very fast backup for Subversion fsfs repositories.
SYNOPSIS
svn-fast-backup [-q] [-k{N|all}] [-f] [-t] [-s] repos_path backup_dir
DESCRIPTION
svn-fast-backup uses rsync snapshots for very fast backup of a Subversion fsfs repository at repos_path to backup_dir/repos-rev, the latest
revision number in the repository. Multiple fsfs backups share data via hardlinks, so old backups are almost free, since a newer revision
of a repository is almost a complete superset of an older revision.
This is good for replacing incremental log-dump+restore-style backups because it is just as space-conserving and even faster; there is no
inter-backup state (old backups are essentially caches); each backup directory is self-contained. It has the same command-line interface
as svn-hot-backup(1) (if you use --force), but only works for fsfs repositories.
svn-fast-backup keeps 64 backups by default and deletes backups older than these; this can be adjusted with the -k option.
OPTIONS
-h, --help
Shows some brief help text.
-q, --quiet
Quieter-than-usual operation.
-k, --keep=N
Keep a specified number of backups; the default is to keep 64.
-k, --keep=all
Do not delete any old backups at all.
-f, --force
Make a new backup even if one with the current revision exists.
-t, --trace
Show actions.
-s, --simulate
Don't perform actions.
AUTHOR
Voluntary contributions made by many individuals. Copyright (C) 2006 CollabNet.
2006-11-09 svn-fast-backup(1)