Sponsored Content
Operating Systems Linux Red Hat Regarding Network Interface Card Post 302919396 by gull04 on Wednesday 1st of October 2014 03:43:55 AM
Old 10-01-2014
Hi jegaraman,

What backup tool are you using?

Regards

Dave
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Multi Network card interface problem

My system info is show below:- #uname -a SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500 and I have two network card as shown below:- #ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies

2. Red Hat

How to configure network interface card in OEL.

Hi I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest. Thanks Ankur (2 Replies)
Discussion started by: ankurk
2 Replies

3. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

4. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies

5. Solaris

Interface card using a lot of bandwith

I have system which is using a lot of bandwidth and this is not a big problem, but how do you troubleshoot this issue? How can I find out which connections are made for one interface card, there are about 5 on this system and I can see how much traffic is going through one interface, but I need... (5 Replies)
Discussion started by: misterx12345
5 Replies

6. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

7. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

8. Red Hat

Interface card link goes down and recovers frequently

Hi Experts, I have an issue where the interface card went down for like four times in last one week in redhat linux server. Every time it goes down, it comes back. 2014 Oct 21 07:22:14 <hostname> kernel: nx_nic: NIC Link is down 2014 Oct 21 07:22:21 <hostname> kernel: nx_nic: NIC Link is... (3 Replies)
Discussion started by: dhanu1985
3 Replies

9. Solaris

Looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A

I'm looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A for Solaris. It used to be on sun-solve, but I fail to find it on the Oracle site. Any help would be very appreciated! (1 Reply)
Discussion started by: Ira28
1 Replies
TDBBACKUP(8)						    System Administration tools 					      TDBBACKUP(8)

NAME
tdbbackup - tool for backing up and for validating the integrity of samba .tdb files SYNOPSIS
tdbbackup [-s suffix] [-v] [-h] DESCRIPTION
This tool is part of the samba(1) suite. tdbbackup is a tool that may be used to backup samba .tdb files. This tool may also be used to verify the integrity of the .tdb files prior to samba startup or during normal operation. If it finds file damage and it finds a prior backup the backup file will be restored. OPTIONS
-h Get help information. -s suffix The -s option allows the adminisistrator to specify a file backup extension. This way it is possible to keep a history of tdb backup files by using a new suffix for each backup. -v The -v will check the database for damages (currupt data) which if detected causes the backup to be restored. COMMANDS
GENERAL INFORMATION The tdbbackup utility can safely be run at any time. It was designed so that it can be used at any time to validate the integrity of tdb files, even during Samba operation. Typical usage for the command will be: tdbbackup [-s suffix] *.tdb Before restarting samba the following command may be run to validate .tdb files: tdbbackup -v [-s suffix] *.tdb Note that Samba 4 can use .ntdb files instead, so you should use ntdbbackup on those files. Samba .tdb files are stored in various locations, be sure to run backup all .tdb file on the system. Important files includes: o secrets.tdb - usual location is in the /usr/local/samba/private directory, or on some systems in /etc/samba. o passdb.tdb - usual location is in the /usr/local/samba/private directory, or on some systems in /etc/samba. o *.tdb located in the /usr/local/samba/var directory or on some systems in the /var/cache or /var/lib/samba directories. VERSION
This man page is correct for version 3 of the Samba suite. AUTHOR
The original Samba software and related utilities were created by Andrew Tridgell. Samba is now developed by the Samba Team as an Open Source project similar to the way the Linux kernel is developed. The tdbbackup man page was written by John H Terpstra. Samba 3.6 06/10/2014 TDBBACKUP(8)
All times are GMT -4. The time now is 09:19 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy