Sponsored Content
Operating Systems Linux Red Hat Regarding Network Interface Card Post 302919392 by jegaraman on Wednesday 1st of October 2014 03:08:48 AM
Old 10-01-2014
Regarding Network Interface Card

Dear All ,

While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.

Pl find the below alert.

Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101 (Threshold = 100000)


Kindly any one explain this alert and also tell how to overcome this.

Thanks in Advance,
Rj
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Multi Network card interface problem

My system info is show below:- #uname -a SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500 and I have two network card as shown below:- #ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies

2. Red Hat

How to configure network interface card in OEL.

Hi I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest. Thanks Ankur (2 Replies)
Discussion started by: ankurk
2 Replies

3. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

4. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies

5. Solaris

Interface card using a lot of bandwith

I have system which is using a lot of bandwidth and this is not a big problem, but how do you troubleshoot this issue? How can I find out which connections are made for one interface card, there are about 5 on this system and I can see how much traffic is going through one interface, but I need... (5 Replies)
Discussion started by: misterx12345
5 Replies

6. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

7. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

8. Red Hat

Interface card link goes down and recovers frequently

Hi Experts, I have an issue where the interface card went down for like four times in last one week in redhat linux server. Every time it goes down, it comes back. 2014 Oct 21 07:22:14 <hostname> kernel: nx_nic: NIC Link is down 2014 Oct 21 07:22:21 <hostname> kernel: nx_nic: NIC Link is... (3 Replies)
Discussion started by: dhanu1985
3 Replies

9. Solaris

Looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A

I'm looking for driver for SunSAI/P 3.0 (Serial Asynchronous Interface) card X2156A for Solaris. It used to be on sun-solve, but I fail to find it on the Oracle site. Any help would be very appreciated! (1 Reply)
Discussion started by: Ira28
1 Replies
alert(3alleg4)							  Allegro manual						    alert(3alleg4)

NAME
alert - Displays a popup alert box. Allegro game programming library. SYNOPSIS
#include <allegro.h> int alert(const char *s1, *s2, *s3, const char *b1, *b2, int c1, c2); DESCRIPTION
Displays a popup alert box, containing three lines of text (s1-s3), and with either one or two buttons. The text for these buttons is passed in `b1' and `b2' (`b2' may be NULL), and the keyboard shortcuts in `c1' and `c2' as ASCII value. Example: if (!exists(CONFIG_FILE)) alert(CONFIG_FILE, "not found.", "Using defaults.", "&Continue", NULL, 'c', 0); RETURN VALUE
Returns 1 or 2 depending on which button was clicked. If the alert is dismissed by pressing ESC when ESC is not one of the keyboard short- cuts, it treats it as a click on the second button (this is consistent with the common "Ok", "Cancel" alert). SEE ALSO
alert3(3alleg4), gui_fg_color(3alleg4), exgui(3alleg4), expackf(3alleg4), exspline(3alleg4) Allegro version 4.4.2 alert(3alleg4)
All times are GMT -4. The time now is 03:15 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy