09-30-2014
Check the port on the FC switch on which that card is connected for errors.
Is multipath software is reporting LUNs on multiple paths ?
Depending on your HBA model there are utilities from the manufacturer to run tests, so you might want to try those.
Also check if the speed is negotiated properly (e.g your port on switch is 8 G with 4 G SFP and your card is 8 G, the speed on the port and the card should be 4 G in this case).
10 More Discussions You Might Find Interesting
1. Solaris
Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies
2. Solaris
I have installed a qlogic HBA card in an E450 Solaris 9 with all the SUNW packages and the latest EPROM version. Configuration reboot was done. An orange light flashes to the right of where the card plugs into the fiber cable after booting, and the following error apprears at the start of the boot... (9 Replies)
Discussion started by: floydm
9 Replies
3. Solaris
I need to install a raid HBA internal card on a T5240. The reason is I have
more drives and the current mother board controller does not support more
than 4 drives.
My question is I have raidctl set up on current drives. If I install new HBA
card do I have to delete current raidctl and... (3 Replies)
Discussion started by: photon
3 Replies
4. Solaris
Hi all
i would like to ask some suggests about my next job!
I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid.
The problem come in if every disk is now controlled by the HBA, how can I install the OS?
No disk is being detected by the OS.
SAS card... (2 Replies)
Discussion started by: kakabobo
2 Replies
5. UNIX for Advanced & Expert Users
I have a V490 that has couple internal disks attached to the same dual-port HBA card that I'm planning attach to the SAN for additional storage.
Would I sacrifice performance if I use the same HBA?
Is it better to throw in a new HBA instead? (1 Reply)
Discussion started by: kiem
1 Replies
6. AIX
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies
7. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
8. Solaris
Hello,
I am very new to solaris so please bear with me. I have 2 machines in question. For both I am trying to get the HBA Card Hardware information such as:
HBA Model Name
HBA Firmware version
HBA Port details
HBA Driver details
First machine is a Solaris 10. When I execute fcinfo... (6 Replies)
Discussion started by: flagman5
6 Replies
9. Solaris
I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage.
in OK prompt, PROBE-SCSI-ALL
showing A5000 fc hdds details in ok prompt.....
but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000... (3 Replies)
Discussion started by: anysystem
3 Replies
10. Solaris
Dear all,
I have a new Oracle Blade X4-2B server, running Solaris 10.
The server comes with a HBA card that will not be used now. It has not fibers connected to it. As a consequence, its leds never stop flashing.
My question is: how to disable this HBA card, without removing it physically... (2 Replies)
Discussion started by: Gus1971
2 Replies
LEARN ABOUT DEBIAN
proslicerl
PROSLICERL(1) Voicetronix Telephony Tools PROSLICERL(1)
NAME
proslicerl - Measure the echo-return loss on Voicetronix FXS telephony modules
SYNOPSIS
proslicerl [options]
DESCRIPTION
The proslicerl utility tests the echo-return from a handset connected to a Voicetronix FXS module, such as those used on the OpenPCI range
of cards. It can scan all available impedance values to find the best match for a particular handset.
When running this test the handset must be off-hook and should have the microphone well muted for the duration of the test.
A series of tones will be played down the line to determine the ERL in several parts of the audio spectrum. You should avoid creating any
other noise on the line while this test is running, or the results may be skewed.
If no --impedance is specified, and the --scan option is not used, then the default impedance value (based on the port's country selection)
will be used.
OPTIONS
The following options are available:
--help, -?
Show summary of options.
--card number
Explicitly select the card to test. Default is card 0.
--port number
Explicitly select the port to test. Default is port 0 of the card being tested.
--impedance number
Test a particular impedance setting [0 - 7].
--scan Test all available impedances.
--playgain db
Set the hardware play gain. Values may range from -12.0 to 12.0.
--recgain db
Set the hardware record gain. Values may range from -12.0 to 12.0.
SEE ALSO
vdaaerl(1)
AUTHOR
Ron Lee, Peter Wintulich, David Rowe, Voicetronix <support@voicetronix.com.au>
This manual page was written by Ron <ron@debian.org>, for the Debian project (but may be used by others).
VPB driver package Oct 11, 2007 PROSLICERL(1)