Hi All ,
I try to install some packages in my global zone...
On the execution of the installion of the script it quits by saying the error
"Non global zone check failed"
Kindly help me in this regard
Thanks in advance,
jeganr (7 Replies)
Hi All
There is one folder in global zone I just want to share the same folder innon global zone. How can i do it?
pls send me script for this. (2 Replies)
Hi All,
I have Solaris-10 M4000 server with VxVM file-system and 7 zones. I rebooted the server and after that one of the zone shows me in running state, but after zlogin, it is showing no df and other output. It is also throwing lot of core dumps
# uname -a
SunOS tssoaq01-ztbgps17 5.10... (7 Replies)
Dear all,
recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes.
I did the following:
host1:
$ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed
$ zpool export zone1
host2:
$ zpool... (2 Replies)
Hi Gurus
I am not able to find the patching procedure for solaris 10 ( sol10 u11) to latest patchset with sun cluster having failover zones so that same I should follow.
Take an instance, there are sol1 and sol2 nodes and having two failover zones like sozone1-rg and sozone2-rg and currently... (1 Reply)
I am planning to do solaris 11 global zone patching having solaris 10 branded zone. I have a doubts on step 8 specially
Can someone clear my step 8 doubts or if anything wrong between step 1 to step 9 please correct that also as I have pretty good idea about Step 10 mean patching in solaris 10... (2 Replies)
I want to migrate a solaris 10 os to solaris 11.4 zone.
I did this
a)Collect some data like id sysid,disks,ip,etc..on solaris10
OK
b)Create this file.cfg with this command on solaris 10
zonep2vchk -c > /migration/sol10.cfg
OK
c)Create the archive flash on Solaris10 (1 Reply)
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)