Hi,
I have broken my laptop hard drive so I would like to put it in an external box to backup my documents.
I have a doubt whether the interface of the hard disk is sata or ide.
Inside notes attached, is reported "controller SATA AHCI" but on the model section is given IDE hard disk
Hi experts,
I need to determine if I have 4GB free space on my UNix server? Is there a way that I can do it instead of executing df -k . in each folder?
Thanks for your help. (3 Replies)
:eek: I use this Solaris to run CMS a call acounting software package for my job. No one could run reports today because it said the this when you logged on
"The following file systems are low, and could adversely affect server performance:
File system /: 99%full"
Can some one please explain... (9 Replies)
Hi,
I can't make the network connection. The cable and hub should be fine since they are working on other systems. I've used 'mktcpip' as well as 'smit tcpip' to configure the interface, and was able to ping the system itself, but I can not ping the gateway - no response. After reboot, the IP... (1 Reply)
Hi,
I have a failed hard disk in my Sun Fire V240. Unfortunately it does not show up in 'cfgadm -al' or in the format command so I cannot unconfigure it and illuminate the blue light on the front to identify it. Is there any way of iluminating the blue lights on the other disks so I can at... (3 Replies)
hi
I've a fresh installation of SCO 5.0.7 on the IDE hard disk.
For SCSI hard disk I can declare, for example blc disk driver using:
# mkdev hd 0 SCSI-0 0 blc 0but it works for IDE hard disk? (3 Replies)
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Good Evening,
2 years ago, I set up an Ubuntu file-server for a friend, who is a photograph amateur. Basically, the server offers a software RAID-5 that can be accessed remotely from a MAC. Unfortunately, I didn't labeled the hard drives (i.e. which physical drive corresponds to the /dev/sdX... (2 Replies)
Hello,
Currently we have a Oracle X4100 ( Solaris 10 ) server with disk failure. Originally our hardware team thought the disk can be hot-swap, when they stood in front of the server, none of the disk failure LED were on, so now we have no idea which disk is the bad one for replacement.
As... (2 Replies)
I am working on VM host and collecting data to identify the type of storage attached to the server which will be migrated to VNX.
it has one ldom created on it
luxadm probe output ---
No Network Array enclosures found in /dev/es
Found Fibre Channel device(s):
Node... (7 Replies)
Discussion started by: kpatel786
7 Replies
LEARN ABOUT DEBIAN
lm-profiler.conf
LM-PROFILER.CONF(8) System Manager's Manual LM-PROFILER.CONF(8)NAME
/etc/laptop-mode/lm-profiler.conf - Configuration file for lm-profiler, a profiler for laptop-mode-tools.
DESCRIPTION
This manual page documents the options that can be set in the /etc/laptop-mode/lm-profiler.conf configuration file. For a description of
what lm-profiler does, see the lm-profiler(8) manpage.
SETTINGS
The syntax of options is OPTION=value.
The following settings are available in lm-profiler.conf:
VERBOSE_OUTPUT
Set this to 1 if you want to see a lot of output when you run lm-profiler, and 0 if you don't want this. Useful for debugging
purposes. (Currently does nothing.)
PROFILE_RUN_LENGTH
The length of a profiling run, in seconds. This should be a while, so that lm-profiler can gather enough information. The default
is 10 minutes (600 seconds).
ACTIVITY_INTERVAL_MIN
ACTIVITY_INTERVAL_MAX
The behaviour that you want to avoid when you have your hard drive spun down, is disk accesses that are spread out over time,
because your hard drive will have to spin up for each access. lm-profiler detects when applications perform disk accesses that
are at least some time apart (otherwise they can be considered part of the same access) but not TOO far apart (otherwise they are
no problem). These settings configure what lm-profiler considers "at least some time apart" and "too far apart", respectively, in
seconds.
RECOMMEND_DEFAULT_SERVICES
DEFAULT_SERVICES
If RECOMMEND_DEFAULT_SERVICES is set to 1 (enabled), then lm-profiler will always suggest turning off the services listed in
DEFAULT_SERVICES (separated by spaces).
IGNORE_PROGRAMS
Programs listed in this option, separated by spaces, will be ignored for disk activity profiling. The default settings (which can
be referenced as $DEF_IGNORE_PROGRAMS) include common utility programs and all programs used by lm-profiler itself.
RECOMMEND_NETWORK_SERVICES
When this option is enabled (value 1), lm-profiler will detect any services that are listening on network ports, and it will sug-
gest that you disable them.
IGNORE_NETWORK_SERVICES
Services listed in this configuration option (separated by spaces) are not suggested as a network service by lm-profiler. The
default values can be accessed as $DEF_IGNORE_NETWORK_SERVICES.
SEE ALSO lm-profiler(8).
laptop_mode(8).
laptop-mode.conf(8).
AUTHOR
This manual page was written by Bart Samwel (bart@samwel.tk). Permission is granted to copy, distribute and/or modify this document under
the terms of the GNU General Public License, Version 2 any later version published by the Free Software Foundation.
LM-PROFILER.CONF(8)