08-25-2014
Hi Night Watcher,
Thanks, I have used nmap several times in the past and do actually have it installed on a machine here - I wasn't aware of the GUI for it so thanks for that. It should save some time on the learning curve
Regards
Dave
6 More Discussions You Might Find Interesting
1. Solaris
when I "ls /dev/dsk/ ", I can see c0t0d0 and c0t2d0;
but when I use format command, I can only see c0t0d0 available;
why this happens? how many disk do I have on the machine? (I do not know that) (2 Replies)
Discussion started by: fredao
2 Replies
2. Shell Programming and Scripting
I am trying to make a bash script to scan subnets to see what hosts are available. Is it correct that you can not make the ping command time out less than a second? The script below works, but can take up to 255 seconds which is a bit long :( Is there a way to solve this using bash only?
<code>... (6 Replies)
Discussion started by: bronkeydain
6 Replies
3. UNIX for Dummies Questions & Answers
Hello All!
New Unix admin here, with a bit of a problem I can't seem to get a straight answer to..
I've been tasked with mapping out the topology (with IPs/Hostnames) of networks...remotely. So, I have SSH access to firewalls, but that's about as far as I can get - how would I go about... (4 Replies)
Discussion started by: Tiyugro
4 Replies
4. AIX
Hi All,
i would like to know if it's possible to know all the IP Addresses of all LPAR's interfaces from HMC (without connect into LPAR).
And if i can know also the "Application" hostname of LPAR from HMC.
Thanks in advance.
Bye
Mario (2 Replies)
Discussion started by: Zio Bill
2 Replies
5. AIX
Hi all,
i must add a new disk on a LPAR.
I've done all the HMC and VIOS Procedure to create a virtual host with disk and assign it to lpar.
I don't remember how i must do on the lpar to see this disk. (i use lvm not veritas).
Thanks in advance and sorry for my english.
Bye
Mario (2 Replies)
Discussion started by: Zio Bill
2 Replies
6. Red Hat
Installed the iscsi target and configured its working fine
While i'm running command in initiator
# iscsiadm --mode discoverydb --type sendtargets --portal 192.168.1.5 --discover
iscsiadm: No portals found
i cant find the LUN1 , its not discovering it what may be the issue and how to... (0 Replies)
Discussion started by: babinlonston
0 Replies
LEARN ABOUT XFREE86
glupwlcurve
GLUPWLCURVE(3G) GLUPWLCURVE(3G)
NAME
gluPwlCurve - describe a piecewise linear NURBS trimming curve
C SPECIFICATION
void gluPwlCurve( GLUnurbs* nurb,
GLint count,
GLfloat* data,
GLint stride,
GLenum type )
PARAMETERS
nurb Specifies the NURBS object (created with gluNewNurbsRenderer).
count Specifies the number of points on the curve.
data Specifies an array containing the curve points.
stride Specifies the offset (a number of single-precision floating-point values) between points on the curve.
type Specifies the type of curve. Must be either GLU_MAP1_TRIM_2 or GLU_MAP1_TRIM_3.
DESCRIPTION
gluPwlCurve describes a piecewise linear trimming curve for a NURBS surface. A piecewise linear curve consists of a list of coordinates of
points in the parameter space for the NURBS surface to be trimmed. These points are connected with line segments to form a curve. If the
curve is an approximation to a curve that is not piecewise linear, the points should be close enough in parameter space that the resulting
path appears curved at the resolution used in the application.
If type is GLU_MAP1_TRIM_2, then it describes a curve in two-dimensional (u and v) parameter space. If it is GLU_MAP1_TRIM_3, then it
describes a curve in two-dimensional homogeneous (u, v, and w) parameter space. See the gluBeginTrim reference page for more information
about trimming curves.
NOTES
To describe a trim curve that closely follows the contours of a NURBS surface, call gluNurbsCurve.
SEE ALSO
gluBeginCurve(3G), gluBeginTrim(3G), gluNewNurbsRenderer(3G), gluNurbsCurve(3G)
GLUPWLCURVE(3G)