08-12-2014
Hey thanks for reply,
sorry didn't see that i have mails formatting my pc etc ... about the situation now everything is under control i see that there is some route in the Windows machines so now everything is fine and work perfect ...
thanks again for helping and sorry for the delay !
9 More Discussions You Might Find Interesting
1. Cybersecurity
Hello! I have some trouble trying to configure a VPN with two gateways. One of them uses IPSec with a single key, 256bits length, specified in /etc/ipsec.secrets. As FreeSwan manual page says, if i put esp=3des-md5-96, will be used a "64bit IV key (internally generated), a 192bit 3des ekey and a... (3 Replies)
Discussion started by: eNTer
3 Replies
2. IP Networking
Hello,
I'm trying to setup a gateway VPN between two routers across an unsecured network between two local networks. The routers are both linux and I'm using the ipsec tools, racoon and setkey. So far hosts from either local net can successfully ping hosts on the other local net without issue.
... (0 Replies)
Discussion started by: salukibob
0 Replies
3. BSD
Hi, this is my first post...:p
Hello Admin :)
Can I have an ask for something with my configuration ?
I have finished some kind of the tutorial to build ipsec site to site, and the "step" has finished completely.
I have a simulation with a local design topology with two PC's (FreeBSD ... (0 Replies)
Discussion started by: aulia
0 Replies
4. UNIX for Advanced & Expert Users
How can i implement Ipsec between two machines in linux_ ubuntu?
any link?? suggestion?? (0 Replies)
Discussion started by: elinaz
0 Replies
5. Cybersecurity
hello,
after configuration ipsec in ip4 I can not ping between client and server whereas I had success ping before configuration!
I also generate different key for AH and ESP as i have shown below.
what is my problem and what should i do to have ping and test the configuration?
code:
... (0 Replies)
Discussion started by: elinaz
0 Replies
6. AIX
Hi Guys,
Please could you tell me if it is possible to have a single rule/filter to allow a certain port range instead of a separate rule for each port?
I'm sure it must be possible but I am unable to find the syntax.
Thanks
Chris (4 Replies)
Discussion started by: chrisstevens
4 Replies
7. IP Networking
Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies
8. IP Networking
Hi all,
I need this as soon as possible to solve it or at least to find out what is the problem.
I have configured IPSec tunnels with Openswan and Cisco ASA, i have established a connection and the ping was fine, but after some time there is request time out from both sites. I don't have ASA... (0 Replies)
Discussion started by: ivancd
0 Replies
9. IP Networking
We are using cyberoam device, VPN IPSEC tunnel is going of frequently even the traffic is throug.
Please suggest what may be the cause for the above mentioned issue.
Also suggest a best tool to monitor the same VPN IPSEC tunnel connectivity. (4 Replies)
Discussion started by: marunmeera
4 Replies
LEARN ABOUT DEBIAN
make_sockdfr
MAKE_SOCKDFR(8) System Manager's Manual MAKE_SOCKDFR(8)
NAME
make_sockdfr - Generates frozen route file for SOCKS server
SYNOPSIS
make_sockdfr [infile [outfile] ]
DESCRIPTION
make_sockdfr reads in a plain-text route file for the SOCKS server and produces a frozen route file as the output.
Both arguments are optional. The default for infile is /etc/sockd.route; the default for outfile is /etc/sockd.fr. You may specify infile
while omitting outfile, but you cannot specify outfile without also speficying infile.
The contents of the frozen route file is essentially the memory image of the parsed input file. Using the frozen route file can reduce the
start-up delay of the SOCKS server program since it no longer has to parse the file contents.
When the SOCKS server starts, it always looks for the frozen route file /etc/sockd.fr first. If that file is not found, it then tries to
use the plain-text route file /etc/sockd.route. If you use frozen route file, you must remember to run make_sockdfr every time after you
modify the plain-text file or the SOCKS server will continue to use the frozen version of a previous route file.
To find out the contents of a frozen route file, use dump_sockdfr.
FILES
/etc/sockd.fr, /etc/sockd.route
SEE ALSO
dump_sockdfr(8), sockd.fr(5), sockd.route(5)
AUTHOR
Ying-Da Lee, yingda@esd.sgi.com or yingda@best.com
May 6, 1996 MAKE_SOCKDFR(8)