08-12-2014
Hey thanks for reply,
sorry didn't see that i have mails formatting my pc etc ... about the situation now everything is under control i see that there is some route in the Windows machines so now everything is fine and work perfect ...
thanks again for helping and sorry for the delay !
9 More Discussions You Might Find Interesting
1. Cybersecurity
Hello! I have some trouble trying to configure a VPN with two gateways. One of them uses IPSec with a single key, 256bits length, specified in /etc/ipsec.secrets. As FreeSwan manual page says, if i put esp=3des-md5-96, will be used a "64bit IV key (internally generated), a 192bit 3des ekey and a... (3 Replies)
Discussion started by: eNTer
3 Replies
2. IP Networking
Hello,
I'm trying to setup a gateway VPN between two routers across an unsecured network between two local networks. The routers are both linux and I'm using the ipsec tools, racoon and setkey. So far hosts from either local net can successfully ping hosts on the other local net without issue.
... (0 Replies)
Discussion started by: salukibob
0 Replies
3. BSD
Hi, this is my first post...:p
Hello Admin :)
Can I have an ask for something with my configuration ?
I have finished some kind of the tutorial to build ipsec site to site, and the "step" has finished completely.
I have a simulation with a local design topology with two PC's (FreeBSD ... (0 Replies)
Discussion started by: aulia
0 Replies
4. UNIX for Advanced & Expert Users
How can i implement Ipsec between two machines in linux_ ubuntu?
any link?? suggestion?? (0 Replies)
Discussion started by: elinaz
0 Replies
5. Cybersecurity
hello,
after configuration ipsec in ip4 I can not ping between client and server whereas I had success ping before configuration!
I also generate different key for AH and ESP as i have shown below.
what is my problem and what should i do to have ping and test the configuration?
code:
... (0 Replies)
Discussion started by: elinaz
0 Replies
6. AIX
Hi Guys,
Please could you tell me if it is possible to have a single rule/filter to allow a certain port range instead of a separate rule for each port?
I'm sure it must be possible but I am unable to find the syntax.
Thanks
Chris (4 Replies)
Discussion started by: chrisstevens
4 Replies
7. IP Networking
Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies
8. IP Networking
Hi all,
I need this as soon as possible to solve it or at least to find out what is the problem.
I have configured IPSec tunnels with Openswan and Cisco ASA, i have established a connection and the ping was fine, but after some time there is request time out from both sites. I don't have ASA... (0 Replies)
Discussion started by: ivancd
0 Replies
9. IP Networking
We are using cyberoam device, VPN IPSEC tunnel is going of frequently even the traffic is throug.
Please suggest what may be the cause for the above mentioned issue.
Also suggest a best tool to monitor the same VPN IPSEC tunnel connectivity. (4 Replies)
Discussion started by: marunmeera
4 Replies
LEARN ABOUT CENTOS
xkbsetautorepeatrate
XkbSetAutoRepeatRate(3) XKB FUNCTIONS XkbSetAutoRepeatRate(3)
NAME
XkbSetAutoRepeatRate - Sets the attributes of the RepeatKeys control for a keyboard device
SYNOPSIS
Bool XkbSetAutoRepeatRate (Display *display, unsigned int device_spec, unsigned int timeout, unsigned int interval);
ARGUMENTS
- display
connection to X server
- device_spec
device to configure, or XkbUseCoreKbd
- timeout
initial delay, ms
- interval
delay between repeats, ms
DESCRIPTION
The core protocol allows only control over whether or not the entire keyboard or individual keys should auto-repeat when held down.
RepeatKeys is a boolean control that extends this capability by adding control over the delay until a key begins to repeat and the rate at
which it repeats. RepeatKeys is coupled with the core auto-repeat control: when RepeatKeys is enabled or disabled, the core auto-repeat is
enabled or disabled and vice versa.
Auto-repeating keys are controlled by two attributes. The first, timeout, is the delay after the initial press of an auto-repeating key and
the first generated repeat event. The second, interval, is the delay between all subsequent generated repeat events. As with all boolean
controls, configuring the attributes that determine how the control operates does not automatically enable the control as a whole.
XkbSetAutoRepeatRate sends a request to the X server to configure the AutoRepeat control attributes to the values specified in timeout and
interval.
XkbSetAutoRepeatRate does not wait for a reply; it normally returns True. Specifying a zero value for either timeout or interval causes the
server to generate a BadValue protocol error. If a compatible version of the Xkb extension is not available in the server, XkbSetAutoRe-
peatRate returns False.
RETURN VALUES
True The XkbSetAutoRepeatRate function returns True normally.
False The XkbSetAutoRepeatRate function returns False if a compatible version of the Xkb extension is not available in the server.
DIAGNOSTICS
BadValue An argument is out of range
X Version 11 libX11 1.6.0 XkbSetAutoRepeatRate(3)