|
|
Sponsored Content
Operating Systems
Linux
Android
Problem with wireless network
Post 302912461 by Corona688 on Friday 8th of August 2014 11:35:42 AM
08-08-2014
|
|
10 More Discussions You Might Find Interesting
1. Cybersecurity
At the moment, I have three computers at home. I want to use boardband for my three computers. But I don't want to use network at home. I have been looking for a product which call OriNoCo USB Cilent. How do I connect to the internet with my computer??
If I post this in a wrong place, please... (0 Replies)
Discussion started by: him
0 Replies
2. IP Networking
Hi,
I have a laptop with a Linksys Wireless G PCMCIA card and a cable connection goin into a router and then a patch lead from the router going to a Linksys Wireless G access point IP 192.168.1.245 with DHCP disabled.
I can connect to the access point from the laptop, but how do I get the... (1 Reply)
Discussion started by: perleo
1 Replies
3. UNIX for Dummies Questions & Answers
I installed solaris 10 x86 on my dell laptop on a partition alongside windows xp. I am able to connect to the internet in xp with both my ethernet local area connection as well as through my wireless network card. But, however i do not have clue as to how to go about it in solaris.
i did not... (0 Replies)
Discussion started by: stakes20
0 Replies
4. Linux
I am running FC4:
Linux maincomp 2.6.13-1.1532_FC4smp
I recently changed the OS from windows XP, and have a feeling that for some reason my wireless network card is slower on Fedora Core 4. The Belkin PCI 802.11b card was automatically detected and configured by FC4 when I installed the OS,... (0 Replies)
Discussion started by: dangral
0 Replies
5. Cybersecurity
Hi all,
How can I monitor packet traffic on my wireless router?
Some info
- my wireless router is netgear wgr614
- everyone can connect it i.e. no password required
- I would like to see where they connect, how they are using the internet connection
I installed wireshark and captured... (3 Replies)
Discussion started by: SaTYR
3 Replies
6. Hardware
hi
Howto identify wireless network card using Live CD? (2 Replies)
Discussion started by: ccc
2 Replies
7. Ubuntu
Hi,
I am a new to Ubuntu linux and trying to learn it. I am using ubuntu 10.04. I am getting problem in setting my wireless network. I set it up properly and was working fine. But suddenly it stopped working, though the wireless icon saying that it is connected, but can't load any page. I... (2 Replies)
Discussion started by: linux_learner
2 Replies
8. Red Hat
Hi,
I am trying to set up a wireless internet connection on my centos OS (6). I can connect via the copper using the internal LAN but cannot get the wireless connection working.
The 2 files that I have configured are:
My wpa_supplicant.conf:
ctrl_interface=/var/run/wpa_supplicant... (1 Reply)
Discussion started by: Duffs22
1 Replies
9. Hardware
Good Day All,
There are numerous results when searching google on this issue, however, none seem to have a solution.
I have read until my eyes bleed and banged my head on the table more than once! :)
I am hoping to resolve this issue -- or at least have a decent workaround.
It is a real... (13 Replies)
Discussion started by: RogerBaran
13 Replies
10. Ubuntu
I run lubuntu from usb (try lubuntu, it's not install on my pc )
And i try to connect to network
I see the network name
And i put the pass
But it's not connect..
I tried to open hot spot on my phone and try to connect and it's not connect
I have edumax n150
Try to install new driver -... (0 Replies)
Discussion started by: popcoern
0 Replies
LEARN ABOUT DEBIAN
macping
MACPING(1) General Commands Manual MACPING(1) NAME
macping - A tool for pinging other RouterOS or mactelnetd devices SYNOPSIS
mactelnet [options] <MAC-Address|hostname> DESCRIPTION
This tool enables you to ping other RouterOS or MAC-Telnetd enabled devices. You can ping either a hostname or a MAC address. If speci- fied, the hostname (identity) will be looked up via MNDP discovery. OPTIONS
These programs follow the usual GNU command line syntax. A summary of options is included below. -f Fast mode, do not wait before sending next ping request. The next ping will be sent immediately when the last ping is received. This cannot be used with -c 0 -s Specify the amount of bytes to send in each ping packet, up to ~1400 bytes. -c Number of packets to send before exiting. A value of 0 means unlimited packets and the tool must be exited with Control + C. -h Show summary of options. -v Show version of program. SEE ALSO
mndp(1), mactelnet(1), mactelnetd(1). AUTHOR
macping was written by Hakon Nessjoen <haakon.nessjoen@gmail.com>. This manual page was written by Hakon Nessjoen <haakon.nessjoen@gmail.com>, for the Debian project (and may be used by others). February 27, 2011 MACPING(1)