08-08-2014
Let me make sure I'm clear on this -- you get packet loss when pinging your modem, but not when pinging the access point?
10 More Discussions You Might Find Interesting
1. Cybersecurity
At the moment, I have three computers at home. I want to use boardband for my three computers. But I don't want to use network at home. I have been looking for a product which call OriNoCo USB Cilent. How do I connect to the internet with my computer??
If I post this in a wrong place, please... (0 Replies)
Discussion started by: him
0 Replies
2. IP Networking
Hi,
I have a laptop with a Linksys Wireless G PCMCIA card and a cable connection goin into a router and then a patch lead from the router going to a Linksys Wireless G access point IP 192.168.1.245 with DHCP disabled.
I can connect to the access point from the laptop, but how do I get the... (1 Reply)
Discussion started by: perleo
1 Replies
3. UNIX for Dummies Questions & Answers
I installed solaris 10 x86 on my dell laptop on a partition alongside windows xp. I am able to connect to the internet in xp with both my ethernet local area connection as well as through my wireless network card. But, however i do not have clue as to how to go about it in solaris.
i did not... (0 Replies)
Discussion started by: stakes20
0 Replies
4. Linux
I am running FC4:
Linux maincomp 2.6.13-1.1532_FC4smp
I recently changed the OS from windows XP, and have a feeling that for some reason my wireless network card is slower on Fedora Core 4. The Belkin PCI 802.11b card was automatically detected and configured by FC4 when I installed the OS,... (0 Replies)
Discussion started by: dangral
0 Replies
5. Cybersecurity
Hi all,
How can I monitor packet traffic on my wireless router?
Some info
- my wireless router is netgear wgr614
- everyone can connect it i.e. no password required
- I would like to see where they connect, how they are using the internet connection
I installed wireshark and captured... (3 Replies)
Discussion started by: SaTYR
3 Replies
6. Hardware
hi
Howto identify wireless network card using Live CD? (2 Replies)
Discussion started by: ccc
2 Replies
7. Ubuntu
Hi,
I am a new to Ubuntu linux and trying to learn it. I am using ubuntu 10.04. I am getting problem in setting my wireless network. I set it up properly and was working fine. But suddenly it stopped working, though the wireless icon saying that it is connected, but can't load any page. I... (2 Replies)
Discussion started by: linux_learner
2 Replies
8. Red Hat
Hi,
I am trying to set up a wireless internet connection on my centos OS (6). I can connect via the copper using the internal LAN but cannot get the wireless connection working.
The 2 files that I have configured are:
My wpa_supplicant.conf:
ctrl_interface=/var/run/wpa_supplicant... (1 Reply)
Discussion started by: Duffs22
1 Replies
9. Hardware
Good Day All,
There are numerous results when searching google on this issue, however, none seem to have a solution.
I have read until my eyes bleed and banged my head on the table more than once! :)
I am hoping to resolve this issue -- or at least have a decent workaround.
It is a real... (13 Replies)
Discussion started by: RogerBaran
13 Replies
10. Ubuntu
I run lubuntu from usb (try lubuntu, it's not install on my pc )
And i try to connect to network
I see the network name
And i put the pass
But it's not connect..
I tried to open hot spot on my phone and try to connect and it's not connect
I have edumax n150
Try to install new driver -... (0 Replies)
Discussion started by: popcoern
0 Replies
LEARN ABOUT DEBIAN
baycom
BAYCOM(9) Kernel Reference Guide BAYCOM(9)
NAME
baycom - amateur (AX.25) packet radio network driver for baycom modems
SYNOPSIS
#include <linux/baycom.h>
#include <linux/hdlcdrv.h>
DESCRIPTION
The driver currently supports three different modems: ser12, par96 and par97.
ser12
This is a very simple 1200 baud AFSK modem. The modem consists only of a modulator/demodulator chip, usually a TI TCM3105. The computer is
responsible for regenerating the receiver bit clock. The modem connects to a serial port, hence the name. Since the serial port is not used
as an async serial port, the kernel driver for serial ports cannot be used, and this driver only supports standard serial hardware (8250,
16450, 16550).
par96
This is a modem for 9600 baud FSK compatible to the G3RUH standard. The modem does all the filtering and regenerates the receiver clock.
Data is transferred from and to the PC via a shift register. The shift register is filled with 16 bits and an interrupt is signalled. The
PC then empties the shift register in a burst. This modem connects to the parallel port, hence the name.
par97
This is a redesign of the par96 modem by Henning Rech, DF9IC. The modem is protocol compatible to par96, but uses only three low power ICs
and can therefore be fed from the parallel port and does not require an additional power supply.
IOCTL CALLS
The ioctl calls follow the implementation in the hdlcdrv.
BAYCOMCTL_GETMODEMTYPE
returns the modem type (i.e. ser12 or par96) and the options in effect (currently only the source of the DCD signal)
BAYCOMCTL_SETMODEMTYPE
sets the modem type and the options. Only superuser can do this.
BAYCOMCTL_GETDEBUG
return some debugging values. Not always available.
SEE ALSO
baycom (9), soundmodem (9), linux/drivers/net/hdlcdrv.c,
AUTHOR
baycom was written by Thomas Sailer, HB9JNX/AE4WA, (t.sailer@alumni.ethz.ch).
Linux 2.1.x 2 October 1996 BAYCOM(9)