6to4relay(1M)						  System Administration Commands					     6to4relay(1M)

NAME

       6to4relay - administer configuration for 6to4 relay router communication

SYNOPSIS

       /usr/sbin/6to4relay

       /usr/sbin/6to4relay [-e] [-a addr]

       /usr/sbin/6to4relay [-d]

       /usr/sbin/6to4relay [-h]

DESCRIPTION

       The  6to4relay  command	is used to configure 6to4 relay router communication. Relay router communication support is enabled by setting the
       value of a variable that stores an IPv4 address within the tun module. This variable is global to all tunnels and defines  the  policy  for
       communication  with  relay routers. By default, the address is set to INADDR_ANY (0.0.0.0), and the kernel interprets the value to indicate
       that support for relay router communication is disabled. Otherwise, support is enabled, and the specified address is used as the IPv4  des-
       tination  address  when packets destined for native IPv6 (non-6to4) hosts are sent through the 6to4 tunnel interface. The 6to4relay command
       uses a project private ioctl to set the variable.

       6to4relay used without any options outputs the current, in-kernel, configuration status. Use the -a option to send packets  to  a  specific
       relay router's unicast address instead of the default anycast address. The address specified with the -a option does not specify the policy
       for receiving traffic from relay routers. The source relay router on a received packet is non-deterministic, since a different relay router
       may be chosen for each sending native IPv6 end-point.

       Configuration  changes  made by using the 6to4relay are not persistent across reboot. The changes will persist in the kernel only until you
       take the tunnel down

OPTIONS

       The 6to4relay command supports the following options:

       -a addr	Use the specified address, addr.

       -e	Enable support for relay router. Use -a addr if it is specified. Otherwise, use the default anycast address, 192.88.99.1.

       -d	Disable support for the relay router.

       -h	Help

OPERANDS

       The following operands are supported:

       addr	A specific relay router's unicast address. addr must be specified as a dotted decimal representation of an  IPv4  address.  Other-
		wise, an error will occur, and the command will fail.

EXAMPLES

       Example 1: Printing the In-Kernel Configuration Status

       Use /usr/sbin/6to4relay without any options to print the in-kernel configuration status.

       example# /usr/sbin/6to4relay

       If 6to4 relay router communication is disabled, the administrator will see the following message:

       6to4relay: 6to4 Relay Router communication support is disabled.

       If 6to4 router communication is enabled, the user will see this message:

       6to4relay: 6to4 Relay Router communication support is enabled.
       IPv4 destination address of Relay Router = 192.88.99.1

EXIT STATUS

       The following exit values are returned:

       0	Successful completion.

       >0	An error occurred.

FILES

       /usr/sbin/6to4relay     The default installation root

ATTRIBUTES

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWcsu			   |
       +-----------------------------+-----------------------------+
       |Interface Stability	     |Evolving			   |
       +-----------------------------+-----------------------------+

SEE ALSO

       ifconfig(1M), attributes(5)

       Huitema, C. RFC 3068, An Anycast Prefix for 6to4 Relay Routers. Network Working Group. June, 2001.

       Carpenter, B. and Moore, K. RFC 3056, Connection of IPv6 Domains via IPv4 Clouds. Network Working Group. February, 2001.

DIAGNOSTICS

       The 6to4relay reports the following messages:

       6to4relay: input (0.0.0.0) is not a valid IPv4 unicast address

	  Example:

	     example# 6to4relay -e -a 0.0.0.0

	  Description:
	     The address specified with the -a option must be a valid unicast address.

       6to4relay: option requires an argument -a
       usage:
	   6to4relay
	   6to4relay -e [-a <addr>]
	   6to4relay -d
	   6to4relay -h

	  Example:

	     example# 6to4relay -e -a

	  Description:
	     The -a option requires an argument.

       usage:
	   6to4relay
	   6to4relay -e [-a <addr>]
	   6to4relay -d
	   6to4relay -h

	  Example:

	     example# 6to4relay -e -d

	  Description:
	     The options specified are not permitted. A usage message is output to the screen.

       usage:
	   6to4relay
	   6to4relay -e [-a <addr>]
	   6to4relay -d
	   6to4relay -h

	  Example:

	     example# 6to4relay -a 1.2.3.4

	  Description:
	     The -e option is required in conjunction with the -a option. A usage message is output to the screen.

       6to4relay: ioctl (I_STR) : Invalid argument

	  Example:

	     example# 6to4relay -e -a 239.255.255.255

	  Description:
	     The address specified with the -a option must not be a class d addr.

SunOS 5.10							    19 Nov 2002 						     6to4relay(1M)