What are you expecting to be on the tape? It rather depends what it was written with.
You could try some of the following:-
I would have expected the first tape drive on your server to be at address /dev/rmt/0m or similar. Does that match what you have?
I'm trying to install a tape drive on a compaq SCO OS 505. well I have gone through the mkdev tape comands and what have you yet no luck. when I reboot and do a simple tape rewind it gives me an error no such device etc.etc. IS there a diference in the xct0 and rct0 a the default?
help.. (2 Replies)
Hello. I have Redhat 8.0 on a laptop. Working good.
I wanted to install the tape drive that is physically attached to it. The tape drive worked fine under Windows98SE. It's one of those parallel QIC-80 drives and I confirmed that it is supported by FTape. It appears that FTape might already... (0 Replies)
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Dear All,
I have a tape drive which has worked for offer 3yrs properly on SCO Openserver Release = 3.2v5.0.5. I tried to clean it all invain. I did a fresh installation of unix of the same OS and did the configuration still didn't bear fruits. The tape is a scsi and the configuration is as... (4 Replies)
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
I've recently been tasked with "refurbishing" an HP Proliant ML370 running SCO 5.0...something. This is primarily used for legacy support and is kept on a shelf for safe keeping. The scope of work includes hardware diagnostics and blowing the dust out.
I have run HP diagnostics on the array,... (1 Reply)
Hi,
Using Redhat 5.7. I have Quantum tape drive connected to the server. I am trying to install the Netbackup software. Just wondering how can I see the Quantum is connected to the server. is any command I run to see the tape drive is connected?
I used to work on Solaris, I used to do... (1 Reply)
Discussion started by: samnyc
1 Replies
LEARN ABOUT ULTRIX
mt
mt(1) General Commands Manual mt(1)Name
mt - magnetic tape manipulating program
Syntax
mt [-f tapename] command [count]
Description
The command permits the operation of a magnetic tape drive.
Options
The -f flag option uses the specified tape device (next argument) in place of either that tape device defined by your TAPE environment
variable (.login or .profile) or /dev/nrmt0h.
Some operations may be performed multiple times by specifying count. By default, performs the requested operation once.
The command argument defines the operation to be performed. Only as many characters as are required to uniquely identify a command need be
specified.
The following is a list of commands:
bsf Backspace count files.
bsr Backspace count records.
cache Allows to use the cache buffer on a tape drive that has the cache buffer feature.
clhrdsf Clear hardware/software problem. Works with tape drives which use the TMSCP tape controller interface This command is
restricted to root access only.
clserex Clear serious exception. Works with tape drives which use the TMSCP tape controller interface
clsub Clear subsystem. Works with tape drives which use the TMSCP tape controller interface This command is restricted to
root access only.
eof, weof Write count end-of-file marks at the current position on the tape.
eotdis Disable end-of-tape detection. When the end of tape is reached, the tape will run off the reel. Only the superuser
can issue this command. The command remains in effect for the device until end-of-tape detection is enabled with the
eoten command.
eoten Enable end-of-tape detection. When the end-of-tape markers are reached, the tape is halted on the reel, between the
two end-of-tape markers. Only the superuser can issue this command. The command remains in effect for the device
until end-of-tape detection is disabled with the eotdis command. This is the default mode after a system boot.
fsf Forward-space count files.
fsr Forward-space count records.
nocache Disables the use of the cache buffer for any tape drive that has the cache buffer feature.
offline, rewoffl Rewind the tape and place the tape unit off-line.
retension Retensions the tape. Retension means moving the tape one complete pass between EOT and BOT.
rewind Rewind the tape.
status Print status information about the tape unit.
Examples
This example shows how to rewind the tape
mt -f /dev/rmt0l rewind
This example shows how to backspace the tape nmt1h three files:
mt -f /dev/nrmt1h bsf 3
This example shows how to write two end-of-file marks at the current position on tape nmt6h:
mt -f /dev/nrmt6h eof 2
Return Values
In shell scripts, returns a 0 exit status when the operation(s) were successful, 1 if the command was unrecognized, and 2 if an operation
failed.
Files
/dev/rmt?h or /dev/rmt?l
Raw magnetic tape interface with rewind when closed
/dev/nmt?h or /dev/nmt?l
Raw magnetic tape interface with no rewind when closed
See Alsodd(1), tar(1), ioctl(2), mtio(4), tms(4), environ(7)mt(1)