07-29-2014
VXVM in POWERHA 6.1
I have created a VxVM disk group in AIX7.1. I have tried to added this VxVM disk group in powerHA 6.1. But in cluster VxVM DGs are not listing. Is there any other procedure to add vxvm diskgroup to hacmp.
Please share me steps for adding vxvm diskgroup to hacmp.
10 More Discussions You Might Find Interesting
1. AIX
hi all
we upgraded hacmp(powerha) from 5.2 to 5.4 recently .
during the failover testing, we found a strange network issue. after standby node took service ip address (172.15.100.8) online at standby NIC, we were able to log in the standby node by telnet 172.15.100.8 which stays at... (1 Reply)
Discussion started by: rs6000er
1 Replies
2. AIX
I've configured multiple clusters using PowerHA 5.5, but never using the 'Two-node cluster configuration assistant'. I removed all the clusters, clean setup, and gave the assistant a try. I've filled in all the necessary options:
Communication Path to Takeover Node
Application Server
... (11 Replies)
Discussion started by: Koen87
11 Replies
3. AIX
I am new in AIX and please forgive my poor english.
I know that AIX allow same subnet IPs for different interfaces, which result in multipath routing / route striping.
My question is,
is there any best practice for the persistent and service IP with same subnet to stay on same interface, or... (5 Replies)
Discussion started by: skeyeung
5 Replies
4. AIX
Hello AIX GURU's
Can anybody tell me the steps to crate shared VG (enhanced concurent) for my Lpars from VIO server?
my questions are:
1.
Should I crate Enhanced Concurent VG in VIO and map it using virtual Scsi to Lpar?
or
2. Can I just create virtual SCSI in VIO and map to Lpar and... (1 Reply)
Discussion started by: Vit0_Corleone
1 Replies
5. AIX
Looking to find PowerHA with 3rd node used for communication (voting node) only. Does anyone use such configuration with IBM products? (2 Replies)
Discussion started by: gogogo
2 Replies
6. AIX
Few questions regarding Power HA ( previously known as HACMP) and VIOS POWERVM IVM ( IBM Virtualization I/O Server )
Is it possible to create HACMP cluster between two VIOS servers
Physical Machine_1
VIOS_SERVER_1
LPAR_1
SHARED_DISK_XX
VIOS_SERVER_2
Physical Machine_2
LPAR_2... (6 Replies)
Discussion started by: filosophizer
6 Replies
7. AIX
hello
ive installed powerha 7.1.3 on two servers aix 6.1.9 6100-09-03-1415
work with dmx4 EMC storgae.
after sync cluster ( terminate with OK ) ive see that the repository disk upper only in one machine :
hdiskpower60 00c7f6b59fc60d9d caavg_private active... (1 Reply)
Discussion started by: ariec
1 Replies
8. AIX
Hey guys, wondering if this is possible to accomplish.
PowerHA SystemMirror7.1 active/passive cluster. Restored a clustered system in test and upgraded to the latest version of PowerHA. Things are working great. However in the interest of time during cut over to the new system, I was hoping to... (4 Replies)
Discussion started by: j_aix
4 Replies
9. AIX
Hello Guys,
I was trying to upgrade the PowerHA from 6.1.0.9 to 7.1.3 in prod cluster. Have snapshot migration and run climgcheck.
1. Run climgcheck on node1(kul1pqcmur01) and it success
2. Upgrade the cluster sw
3. Run climgcheck on node2(kul1pqcmur02) and it failed with below errors
... (6 Replies)
Discussion started by: novaothers
6 Replies
10. AIX
Hi All,
As per the IBM upgrade/support matrix
IBM Techdocs Technote: PowerHA for AIX Version Compatibility Matrix
we can't do online upgrade or rolling migration from powerha v7.1.0 to v7.1.3. on AIX61_TL9_SP4, So we are following the steps as below ...
1 ) Bring down the cluster
2 )... (2 Replies)
Discussion started by: linux.amrit
2 Replies
LEARN ABOUT HPUX
vgrestore
vgrestore(1M) vgrestore(1M)
NAME
vgrestore - restore a VxVM disk group back to an LVM volume group
SYNOPSIS
/etc/vx/bin/vgrestore vg_name
DESCRIPTION
The vgrestore command restores a Logical Volume Manager (LVM) volume group that was previously converted to a VxVM disk group by the vxvm-
convert utility.
ARGUMENTS
vg_name
Specifies the name of a volume group that was converted to a VxVM disk group by the vxvmconvert utility.
EXIT CODES
vgrestore exits with one of the following values:
0 Successful completion.
>0 Failure; an error occurred.
WARNINGS
vgrestore functions only on VxVM disk groups that were converted from LVM volume groups by the vxvmconvert command.
It is a good idea to back up user data before running vgrestore, and restore it after the vgrestore completes, as vgrestore can only
restore a logical volume back to the state it was in before conversion to VxVM. If data changed on the volume while it was a VxVM volume,
the changes won't be reflected on the volume after being restored to LVM.
As part of the original conversion process, applications that once referenced the now-converted LVM volume's path names may have changed to
reference VxVM volume special device file names. Alternatively, special device file path names originally representing the now-converted
LVM volumes may have changed to symbolic links pointing to the VxVM volume path names. Be sure to undo these actions when restoring back
to LVM.
Do not use vgrestore unless you are certain that you want to restore LVM volume groups. After vgrestore this is run, the VxVM disks will
no longer exist.
EXAMPLES
To restore the LVM volume group vg03 that was converted by vxvmconvert to the VxVM disk group dg03, enter:
vgcfgrestore vg03
SEE ALSO
vxvmconvert(1M)
Veritas Volume Manager Migration Guide
VxVM 5.0.31.1 24 Mar 2008 vgrestore(1M)