07-28-2014
Quote:
Hmmm.
How do you "physically remove" a single core in a 4 core CPU?
I've always wanted to try dynamite.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I'm new to UNIX....
I'm running SCO UNIX and would like to disable routed daemon from being start at boot time.
How should I do this????? Please help. (2 Replies)
Discussion started by: rrivas
2 Replies
2. UNIX for Dummies Questions & Answers
I want to upgrade from Red Hat Linux 8.0 to Fedora Core 3. I have already downloaded FC3 on CD's. My current config. on my PC is that I have Win XP on primary hard drive and Red Hat 8.0 on another hard drive. Because my Compaq Presario reserves the first cylinder of my primary hard drive, I... (1 Reply)
Discussion started by: Mark McWilliams
1 Replies
3. Solaris
Hi,
I'm looking for a command to be able to disable a network card under the boot PROM.
I need it to force my Jumpstart to use the Ethernet card of my server (V880) instead of my fiber card (gem0).
Thanks,
Fabien (6 Replies)
Discussion started by: unclefab
6 Replies
4. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
5. Solaris
All -
would you please some one help me to disable telnet on Solaris?
/etc/inetd.conf
Thanks :confused: (11 Replies)
Discussion started by: March_2007
11 Replies
6. Solaris
Hi
Is there anyway to disable all logs/logging (lastlog, sulog, messages etc.) in Solaris 9&10? I know this is not recommended but i just want to know if this is possible.
TIA
Reddy (8 Replies)
Discussion started by: reddyr
8 Replies
7. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
8. Solaris
I've new installed Solaris 11 on Sparc T4-1.
I'd like to disable IPv6 but with no luck.
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
net0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 2
inet... (6 Replies)
Discussion started by: samer.odeh
6 Replies
9. Solaris
Hello,
I have a problem with my machine that won't boot properly.
The story is that I installed a software called apcupsd, which is a control application for my APC battery UPS. I have used version 3.14.10 earlier, but as part of restoring my previously crashed os harddrive I wanted to... (18 Replies)
Discussion started by: Zorken
18 Replies
LEARN ABOUT NETBSD
fincore
FINCORE(1) BSD General Commands Manual FINCORE(1)
NAME
fincore -- query in-core status of file pages
SYNOPSIS
fincore [-qs] file ...
DESCRIPTION
The fincore utility queries and displays in-core status of specified files.
Note that the result can already be stale when being output due to other activities in the system. Thus it should be used only for advisory
purposes.
The fincore utility accepts the following options.
-q The quiet mode. Outputs nothing unless the file has in-core pages.
-s The summary mode. Only shows number of pages.
EXAMPLES
The following example shows that /bin/cat and /bin/cp are fully cached in-core while the other executables are not in-core. numbers shown in
the default output are page indexes in the file of each in-core pages.
% fincore /bin/c*
/bin/cat: 0 1 2 3
/bin/chio:
/bin/chmod:
/bin/cp: 0 1 2 3 4 5
/bin/cpio:
/bin/csh:
% fincore -s /bin/c*
/bin/cat: 4 / 4 in-core pages (100.00%)
/bin/chio: 0 / 5 in-core pages (0.00%)
/bin/chmod: 0 / 3 in-core pages (0.00%)
/bin/cp: 6 / 6 in-core pages (100.00%)
/bin/cpio: 0 / 36 in-core pages (0.00%)
/bin/csh: 0 / 41 in-core pages (0.00%)
SEE ALSO
mincore(2)
AUTHORS
The fincore utility is written by YAMAMOTO Takashi.
CAVEATS
The concept of page cache is an implementation detail of the kernel. The fincore utility works using some assumptions on the current imple-
mentation. Thus it might stop working in a future version of NetBSD.
BUGS
The amount of CPU time the current implementation of fincore utility would take is roughly proportional to the file sizes. Ideally it should
be proportional to the number of in-core pages.
BSD
January 5, 2012 BSD