07-28-2014
Quote:
Originally Posted by
achenle
.... and physically remove them if you don't want the OS to ever "see" them.
Hmmm.
How do you "physically remove" a single core in a 4 core CPU?
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I'm new to UNIX....
I'm running SCO UNIX and would like to disable routed daemon from being start at boot time.
How should I do this????? Please help. (2 Replies)
Discussion started by: rrivas
2 Replies
2. UNIX for Dummies Questions & Answers
I want to upgrade from Red Hat Linux 8.0 to Fedora Core 3. I have already downloaded FC3 on CD's. My current config. on my PC is that I have Win XP on primary hard drive and Red Hat 8.0 on another hard drive. Because my Compaq Presario reserves the first cylinder of my primary hard drive, I... (1 Reply)
Discussion started by: Mark McWilliams
1 Replies
3. Solaris
Hi,
I'm looking for a command to be able to disable a network card under the boot PROM.
I need it to force my Jumpstart to use the Ethernet card of my server (V880) instead of my fiber card (gem0).
Thanks,
Fabien (6 Replies)
Discussion started by: unclefab
6 Replies
4. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
5. Solaris
All -
would you please some one help me to disable telnet on Solaris?
/etc/inetd.conf
Thanks :confused: (11 Replies)
Discussion started by: March_2007
11 Replies
6. Solaris
Hi
Is there anyway to disable all logs/logging (lastlog, sulog, messages etc.) in Solaris 9&10? I know this is not recommended but i just want to know if this is possible.
TIA
Reddy (8 Replies)
Discussion started by: reddyr
8 Replies
7. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
8. Solaris
I've new installed Solaris 11 on Sparc T4-1.
I'd like to disable IPv6 but with no luck.
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
net0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 2
inet... (6 Replies)
Discussion started by: samer.odeh
6 Replies
9. Solaris
Hello,
I have a problem with my machine that won't boot properly.
The story is that I installed a software called apcupsd, which is a control application for my APC battery UPS. I have used version 3.14.10 earlier, but as part of restoring my previously crashed os harddrive I wanted to... (18 Replies)
Discussion started by: Zorken
18 Replies
LEARN ABOUT DEBIAN
tpm_setpresence
tpm_setpresence(8) System Manager's Manual tpm_setpresence(8)
TPM Management - tpm_setpresence
NAME
tpm_setpresence- change TPM physical presence states or settings
SYNOPSIS
tpm_setpresence [OPTION]
DESCRIPTION
tpm_setpresence reports the status of the TPM's flags regarding physical presence. This is the default behavior and also accessible via
the --status option. Requesting a report of this status prompts for the owner password. The --assert option changes the TPM to the
physically present state. The --clear option changes the TPM to the not present state. The --lock option locks the TPM to the current
physical presence state for the current boot cycle. The --enable-cmd option allows the TPM to accept local commands to toggle physical
presence states. The --disable-cmd option prevents the TPM from accepting local commands to toggle physical presence states. The --enable-
hw option allows the TPM to accept hardware signals to toggle physical presence states. The --disable-hw option prevents the TPM from
accepting hardware signals to toggle physical presence states. The --set-lifetime-lock option locks the Command and Hardware enablement
flags in their current state permenantly. This option can never be undone. The system will attempt to use the owner password to display
the current states before preceding unless the --yes option is given to answer yes to all questions. All changes are made with the
TSC_Physical Presence API.
-h, --help
Display command usage info.
-v, --version
Display command version info.
-l, --log [none|error|info|debug]
Set logging level.
-u, --unicode
Use TSS UNICODE encoding for passwords to comply with applications using TSS popup boxes
-a, --assert
Assert that an admin is physically present at the machine.
-c, --clear
Remove the assertion that an admin is physically present at the machine.
--lock Lock the assertions of physical presence in there current states until a reboot.
--enable-cmd
Allow use of commands to signal an admin is physically present.
--disable-cmd
Disallow use of commands to signal an admin is physically present.
--enable-hw
Allow use of hardware signals to signal an admin is physically present.
--disable-hw
Disallow use of hardware signals to signal an admin is physically present.
--set-lifetime-lock
Allow no further changes to the flags controling how physical presence can be signaled. This is PERMANENT.
-y, --yes
Answer yes to all questions. Only applicable with --set-lifetime-lock.
-z, --well-known
Authenticate using 20 bytes of zeros as owner password (the default TSS Well Known Secret), instead of prompting for an owner
password.
SEE ALSO
tpm_version(1), tpm_setenable(8), tpm_setactive(8), tpm_setownable(8), tcsd(8)
REPORTING BUGS
Report bugs to <trousers-users@lists.sourceforge.net>
TPM Management 2005-05-06 tpm_setpresence(8)