I'm new to UNIX....
I'm running SCO UNIX and would like to disable routed daemon from being start at boot time.
How should I do this????? Please help. (2 Replies)
I want to upgrade from Red Hat Linux 8.0 to Fedora Core 3. I have already downloaded FC3 on CD's. My current config. on my PC is that I have Win XP on primary hard drive and Red Hat 8.0 on another hard drive. Because my Compaq Presario reserves the first cylinder of my primary hard drive, I... (1 Reply)
Hi,
I'm looking for a command to be able to disable a network card under the boot PROM.
I need it to force my Jumpstart to use the Ethernet card of my server (V880) instead of my fiber card (gem0).
Thanks,
Fabien (6 Replies)
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Hi
Is there anyway to disable all logs/logging (lastlog, sulog, messages etc.) in Solaris 9&10? I know this is not recommended but i just want to know if this is possible.
TIA
Reddy (8 Replies)
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
I've new installed Solaris 11 on Sparc T4-1.
I'd like to disable IPv6 but with no luck.
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
net0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 2
inet... (6 Replies)
Hello,
I have a problem with my machine that won't boot properly.
The story is that I installed a software called apcupsd, which is a control application for my APC battery UPS. I have used version 3.14.10 earlier, but as part of restoring my previously crashed os harddrive I wanted to... (18 Replies)
Discussion started by: Zorken
18 Replies
LEARN ABOUT OSF1
rc2
rc2(8) System Manager's Manual rc2(8)NAME
rc2 - Run command script executed when entering a multiuser run level
SYNOPSIS
rc2
DESCRIPTION
The rc2 script contains run commands that enable initialization of the system to a multiuser state; run level 2. In addition to commands
listed within the script itself, rc2 contains instructions to run certain commands found in the /sbin/rc2.d directory. The script defines
the conditions under which the commands execute; some commands run if the system is booting, other commands execute if the system is chang-
ing run levels.
By convention, files in the /sbin/rc2.d directory begin with either the letter "K" or the letter "S" and are followed by a two-digit number
and a filename; for example: K00lpd S00savecore S25uucp
In general, the system starts commands that begin with the letter "S" and stops commands that begin with the letter "K." Commands that
begin with the letter "K" run only when the system is changing run levels from a higher to a lower level. Commands that begin with the
letter "S" run in all cases. The numbering of commands in the /sbin/rc2.d directory is important since the numbers are sorted and the com-
mands are run in ascending order. Files in the /sbin/rc2.d directory are normally links to files in the /etc/init.d directory.
An entry in the inittab file causes the system to execute the rc2 run commands, for example: s2:23:wait:/sbin/rc2 < /dev/console >
/dev/console 2>&1
The following operations are typical of those that result from executing the rc2 script and the commands located in the /sbin/rc2.d direc-
tory. The operation depends on which state the system is entering or exiting. Setting the time zone Checking the current run level Stop-
ping network services and daemons Starting (or stopping) system services and daemons Starting the cron daemon Setting up paging and dump
facilities Setting up uucp files
Setting the TIMEZONE variable is one of the first operations completed by the rc2 script. This action provides the default time zone for
subsequent commands.
FILES
Specifies the command path Specifies the directory of commands that correspond to the run level
RELATED INFORMATION
Commands: init(8), rc0(8), rc3(8) delim off
rc2(8)