07-27-2014
You are absolutely right Sir!
Many thanks for your help and kind regards,
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Sorry to keep bothering you guys like this with all these boring, related questions. But here's one that should be more readily answerable.
What command or file should i use to get the speed/data rate of a network link? This is the capacity speed for instance 10Mbps or 100 Mbps in the case of the... (2 Replies)
Discussion started by: mint1981
2 Replies
2. UNIX for Advanced & Expert Users
Hello, everyone:
i encounter a problem these days , pls help me ,thanks in advance.
my env:
machine: ES40 A ES40 B
os: true64 Unix 4.0f
note: src.tar 8M network card speed 100M
my problem:
... (3 Replies)
Discussion started by: q30
3 Replies
3. HP-UX
Hello,
can anyone tell me how to change network speed or duplex speed...don't understand the concept why that is imp when the server comes back up to check up on it.
Basically have to make sure that the setting from the orginial speed. (2 Replies)
Discussion started by: catwomen
2 Replies
4. IP Networking
Hi all, one of my Sun Box facing the problem.
The network port i had set to Auto-Negotiated and i had edited the /etc/system/ file in the Sun box as below:
set hme:hme_adv_autoneg_cap=1
set hme:hme_adv_100fdx_cap=0
set hme:hme_adv_100hdx_cap=0
But when i checked the /var/adm/messages/, it... (0 Replies)
Discussion started by: AirWalker83
0 Replies
5. Solaris
I recently learned that Sun Solaris network cards (ce devices) have problems with ndd -get commands. I did some searching and found out about the netstat -k command to show me the link speed. What is the best way to change the link speed (both one time and permanently)?
I am running Solaris 9... (7 Replies)
Discussion started by: hshapiro
7 Replies
6. IP Networking
hello i have a ubuntu ssh server that i can acess from any of my comnputers but only if they are on the same wireless network as the server. i tested trhis my tehtehring my samsung blackjack to my windows partition and installing openssh to windows it works when windows is on the wireless but no... (1 Reply)
Discussion started by: old noob
1 Replies
7. Solaris
i have first server (sun solaris 5.10) for example X(172.x.x.x)
and i have second server (sun solaris 5.10) for example Y(192.x.x.x)
also we have 3 clients PC (windows XP)(172.x.x.x)
the X server connect to Y server and to clients PC
* who to know the network speed between X and Y
* who to... (1 Reply)
Discussion started by: anwar
1 Replies
8. IP Networking
I have two PCs, witch have Linux Ubuntu.
I want to connect those computers by a local network, but I know right anything about the network.
I have a modem (not router) and a router that i don't use.
The desktop pc have 2 network cards. (eth0 eth1). The modem is on eth1.
Anyone help me!... (4 Replies)
Discussion started by: mghis
4 Replies
9. UNIX for Dummies Questions & Answers
After installing PV (Para virtual drivers) drivers I m not able to check the network speed of my Ethernet port.
Please check the output of mii-tool and ethtool.
# mii-tool eth0
SIOCGMIIPHY on 'eth0' failed: Operation not supported
# ethtool eth0
Settings for eth0:
Link... (2 Replies)
Discussion started by: pinga123
2 Replies
10. Hardware
Dear all,
Would you know how to measure the max speed of a WIFI connection between a router and a laptop for instance?
Many thanks for your help!
Regards, (3 Replies)
Discussion started by: freddie50
3 Replies
IXGBE(4) BSD Kernel Interfaces Manual IXGBE(4)
NAME
ixgbe -- Intel(R) 10Gb Ethernet driver for the FreeBSD operating system
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device ixgbe
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_ixgbe_load="YES"
DESCRIPTION
The ixgbe driver provides support for PCI 10Gb Ethernet adapters based on the Intel 82598EB Intel(R) Network Connections. The driver sup-
ports Jumbo Frames, MSIX, TSO, and RSS.
For questions related to hardware requirements, refer to the documentation supplied with your Intel 10GbE adapter. All hardware requirements
listed apply to use with FreeBSD.
Support for Jumbo Frames is provided via the interface MTU setting. Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility
configures the adapter to receive and transmit Jumbo Frames. The maximum MTU size for Jumbo Frames is 16114.
This driver version supports VLANs. For information on enabling VLANs, see ifconfig(8).
HARDWARE
The ixgbe driver supports the following cards:
o Intel(R) 10 Gigabit XF SR/AF Dual Port Server Adapter
o Intel(R) 10 Gigabit XF SR/LR Server Adapter
o Intel(R) 82598EB 10 Gigabit AF Network Connection
o Intel(R) 82598EB 10 Gigabit AT CX4 Network Connection
DIAGNOSTICS
ixgbe%d: Unable to allocate bus resource: memory A fatal initialization error has occurred.
ixgbe%d: Unable to allocate bus resource: interrupt A fatal initialization error has occurred.
ixgbe%d: watchdog timeout -- resetting The device has stopped responding to the network, or there is a problem with the network connection
(cable).
SUPPORT
For general information and support, go to the Intel support website at: http://support.intel.com.
If an issue is identified with the released source code on the supported kernel with a supported adapter, email the specific information
related to the issue to <freebsd@intel.com>.
SEE ALSO
altq(4), arp(4), netintro(4), ng_ether(4), polling(4), vlan(4), ifconfig(8)
HISTORY
The ixgbe device driver first appeared in FreeBSD 7.0.
AUTHORS
The ixgbe driver was written by Intel Corporation <freebsd@intel.com>.
BSD
December 19, 2010 BSD