Sponsored Content
Full Discussion: Local Network Speed
Operating Systems Linux Red Hat Local Network Speed Post 302910671 by freddie50 on Saturday 26th of July 2014 06:36:58 PM
Old 07-26-2014
Local Network Speed

Dear All,

I have an intel NUC running CentOS 7 and physically connected to my Netgear CBVG834G router.
They both have Gigabit Ethernet cards and supposedly a top notch network cable connecting the two devices.
But when I run ethtool the connection is only running at 100Mbit/s

What can I do to boost this connection?

Many thanks for your help and keep up the good work!

Cheers,
freddie50
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Speed of network link

Sorry to keep bothering you guys like this with all these boring, related questions. But here's one that should be more readily answerable. What command or file should i use to get the speed/data rate of a network link? This is the capacity speed for instance 10Mbps or 100 Mbps in the case of the... (2 Replies)
Discussion started by: mint1981
2 Replies

2. UNIX for Advanced & Expert Users

network speed is slow

Hello, everyone: i encounter a problem these days , pls help me ,thanks in advance. my env: machine: ES40 A ES40 B os: true64 Unix 4.0f note: src.tar 8M network card speed 100M my problem: ... (3 Replies)
Discussion started by: q30
3 Replies

3. HP-UX

Network speed on HPUX

Hello, can anyone tell me how to change network speed or duplex speed...don't understand the concept why that is imp when the server comes back up to check up on it. Basically have to make sure that the setting from the orginial speed. (2 Replies)
Discussion started by: catwomen
2 Replies

4. IP Networking

network speed not tale with the port setting

Hi all, one of my Sun Box facing the problem. The network port i had set to Auto-Negotiated and i had edited the /etc/system/ file in the Sun box as below: set hme:hme_adv_autoneg_cap=1 set hme:hme_adv_100fdx_cap=0 set hme:hme_adv_100hdx_cap=0 But when i checked the /var/adm/messages/, it... (0 Replies)
Discussion started by: AirWalker83
0 Replies

5. Solaris

Change speed on network card

I recently learned that Sun Solaris network cards (ce devices) have problems with ndd -get commands. I did some searching and found out about the netstat -k command to show me the link speed. What is the best way to change the link speed (both one time and permanently)? I am running Solaris 9... (7 Replies)
Discussion started by: hshapiro
7 Replies

6. IP Networking

ssh server is attachable from local network not from another network

hello i have a ubuntu ssh server that i can acess from any of my comnputers but only if they are on the same wireless network as the server. i tested trhis my tehtehring my samsung blackjack to my windows partition and installing openssh to windows it works when windows is on the wireless but no... (1 Reply)
Discussion started by: old noob
1 Replies

7. Solaris

network speed

i have first server (sun solaris 5.10) for example X(172.x.x.x) and i have second server (sun solaris 5.10) for example Y(192.x.x.x) also we have 3 clients PC (windows XP)(172.x.x.x) the X server connect to Y server and to clients PC * who to know the network speed between X and Y * who to... (1 Reply)
Discussion started by: anwar
1 Replies

8. IP Networking

Local network?

I have two PCs, witch have Linux Ubuntu. I want to connect those computers by a local network, but I know right anything about the network. I have a modem (not router) and a router that i don't use. The desktop pc have 2 network cards. (eth0 eth1). The modem is on eth1. Anyone help me!... (4 Replies)
Discussion started by: mghis
4 Replies

9. UNIX for Dummies Questions & Answers

how to see network speed of virtual linux machine?

After installing PV (Para virtual drivers) drivers I m not able to check the network speed of my Ethernet port. Please check the output of mii-tool and ethtool. # mii-tool eth0 SIOCGMIIPHY on 'eth0' failed: Operation not supported # ethtool eth0 Settings for eth0: Link... (2 Replies)
Discussion started by: pinga123
2 Replies

10. Hardware

How to test the speed of your WIFI network?

Dear all, Would you know how to measure the max speed of a WIFI connection between a router and a laptop for instance? Many thanks for your help! Regards, (3 Replies)
Discussion started by: freddie50
3 Replies
IXGB(4) 						   BSD Kernel Interfaces Manual 						   IXGB(4)

NAME
ixgb -- Intel(R) PRO/10GbE Ethernet driver for the FreeBSD operating system SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file: device ixgb Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_ixgb_load="YES" DESCRIPTION
The ixgb driver provides support for PCI Gigabit Ethernet adapters based on the Intel 82597EX Ethernet controller chips. The driver supports Transmit/Receive checksum offload and Jumbo Frames. For questions related to hardware requirements, refer to the documentation supplied with your Intel PRO/10GbE adapter. All hardware require- ments listed apply to use with FreeBSD. Support for Jumbo Frames is provided via the interface MTU setting. Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility configures the adapter to receive and transmit Jumbo Frames. The maximum MTU size for Jumbo Frames is 16114. This driver version supports VLANs. For information on enabling VLANs, see ifconfig(8). HARDWARE
The ixgb driver supports the following cards: o Intel PRO/10GbE LR Server Adapter o Intel PRO/10GbE SR Server Adapter DIAGNOSTICS
ixgb%d: Unable to allocate bus resource: memory A fatal initialization error has occurred. ixgb%d: Unable to allocate bus resource: interrupt A fatal initialization error has occurred. ixgb%d: watchdog timeout -- resetting The device has stopped responding to the network, or there is a problem with the network connection (cable). SUPPORT
For general information and support, go to the Intel support website at: http://support.intel.com. If an issue is identified with the released source code on the supported kernel with a supported adapter, email the specific information related to the issue to <freebsd@intel.com>. SEE ALSO
arp(4), em(4), netintro(4), ng_ether(4), polling(4), vlan(4), ifconfig(8) HISTORY
The ixgb device driver first appeared in FreeBSD 4.11 and FreeBSD 5.3. AUTHORS
The ixgb driver was written by Intel Corporation <freebsd@intel.com>. BSD
August 18, 2006 BSD
All times are GMT -4. The time now is 12:46 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy