07-25-2014
How do I disable a core(or more) while boot up in Solaris 10?
Hi,
I have 4 cores in my PC. I know how to disable a core using psradm -f command after boot up. But I want to disable while boot up (permanently).
1) I want only 1 core. How to disable all other cores while boot up?
2) I need to disable 2 cores. How to disable all other cores while boot up?
I need the best way.
Thank you.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I'm new to UNIX....
I'm running SCO UNIX and would like to disable routed daemon from being start at boot time.
How should I do this????? Please help. (2 Replies)
Discussion started by: rrivas
2 Replies
2. UNIX for Dummies Questions & Answers
I want to upgrade from Red Hat Linux 8.0 to Fedora Core 3. I have already downloaded FC3 on CD's. My current config. on my PC is that I have Win XP on primary hard drive and Red Hat 8.0 on another hard drive. Because my Compaq Presario reserves the first cylinder of my primary hard drive, I... (1 Reply)
Discussion started by: Mark McWilliams
1 Replies
3. Solaris
Hi,
I'm looking for a command to be able to disable a network card under the boot PROM.
I need it to force my Jumpstart to use the Ethernet card of my server (V880) instead of my fiber card (gem0).
Thanks,
Fabien (6 Replies)
Discussion started by: unclefab
6 Replies
4. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
5. Solaris
All -
would you please some one help me to disable telnet on Solaris?
/etc/inetd.conf
Thanks :confused: (11 Replies)
Discussion started by: March_2007
11 Replies
6. Solaris
Hi
Is there anyway to disable all logs/logging (lastlog, sulog, messages etc.) in Solaris 9&10? I know this is not recommended but i just want to know if this is possible.
TIA
Reddy (8 Replies)
Discussion started by: reddyr
8 Replies
7. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
8. Solaris
I've new installed Solaris 11 on Sparc T4-1.
I'd like to disable IPv6 but with no luck.
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
net0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 2
inet... (6 Replies)
Discussion started by: samer.odeh
6 Replies
9. Solaris
Hello,
I have a problem with my machine that won't boot properly.
The story is that I installed a software called apcupsd, which is a control application for my APC battery UPS. I have used version 3.14.10 earlier, but as part of restoring my previously crashed os harddrive I wanted to... (18 Replies)
Discussion started by: Zorken
18 Replies
SIBA(4) BSD Kernel Interfaces Manual SIBA(4)
NAME
siba -- Sonic Inc. Silicon Backplane driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device siba
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
siba_load="YES"
DESCRIPTION
The siba driver supports the Sonic Inc. Silicon Backplane, the interblock communications architecture that can be found in most Broadcom
wireless NICs.
A bus connects all of the Silicon Backplane's functional blocks. These functional blocks, known as cores, use the Open Core Protocol (OCP)
interface to communicate with agents attached to the Silicon Backplane.
Each NIC uses a chip from the same chip family. Each member of the family contains a different set of cores, but shares basic architectural
features such as address space definition, interrupt and error architecture, and backplane register definitions.
Each core can have an initiator agent that passes read and write requests onto the system backplane and a target agent that returns responses
to those requests. Not all cores contain both an initiator and a target agent. Initiator agents are present in cores that contain host
interfaces (PCI, PCMCIA), embedded processors (MIPS), or DMA processors associated with communications cores.
All cores other than PCMCIA have a target agent.
SEE ALSO
bwn(4)
HISTORY
The siba device driver first appeared in FreeBSD 8.0.
AUTHORS
The siba driver was written by Bruce M. Simpson <bms@FreeBSD.org> and Weongyo Jeong <weongyo@FreeBSD.org>.
CAVEATS
Host mode is not supported at this moment.
BSD
January 8, 2010 BSD