Hello! I have some trouble trying to configure a VPN with two gateways. One of them uses IPSec with a single key, 256bits length, specified in /etc/ipsec.secrets. As FreeSwan manual page says, if i put esp=3des-md5-96, will be used a "64bit IV key (internally generated), a 192bit 3des ekey and a... (3 Replies)
Hello,
I'm trying to setup a gateway VPN between two routers across an unsecured network between two local networks. The routers are both linux and I'm using the ipsec tools, racoon and setkey. So far hosts from either local net can successfully ping hosts on the other local net without issue.
... (0 Replies)
Hi, this is my first post...:p
Hello Admin :)
Can I have an ask for something with my configuration ?
I have finished some kind of the tutorial to build ipsec site to site, and the "step" has finished completely.
I have a simulation with a local design topology with two PC's (FreeBSD ... (0 Replies)
hello,
after configuration ipsec in ip4 I can not ping between client and server whereas I had success ping before configuration!
I also generate different key for AH and ESP as i have shown below.
what is my problem and what should i do to have ping and test the configuration?
code:
... (0 Replies)
Hi Guys,
Please could you tell me if it is possible to have a single rule/filter to allow a certain port range instead of a separate rule for each port?
I'm sure it must be possible but I am unable to find the syntax.
Thanks
Chris (4 Replies)
Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Hi all,
I need this as soon as possible to solve it or at least to find out what is the problem.
I have configured IPSec tunnels with Openswan and Cisco ASA, i have established a connection and the ping was fine, but after some time there is request time out from both sites. I don't have ASA... (0 Replies)
We are using cyberoam device, VPN IPSEC tunnel is going of frequently even the traffic is throug.
Please suggest what may be the cause for the above mentioned issue.
Also suggest a best tool to monitor the same VPN IPSEC tunnel connectivity. (4 Replies)
Discussion started by: marunmeera
4 Replies
LEARN ABOUT OPENDARWIN
iptables-save
IPTABLES-SAVE(8) iptables 1.6.1 IPTABLES-SAVE(8)NAME
iptables-save -- dump iptables rules to stdout
ip6tables-save -- dump iptables rules to stdout
SYNOPSIS
iptables-save [-M modprobe] [-c] [-t table]
ip6tables-save [-M modprobe] [-c] [-t table]
DESCRIPTION
iptables-save and ip6tables-save are used to dump the contents of IP or IPv6 Table in easily parseable format to STDOUT. Use I/O-redirect-
ion provided by your shell to write to a file.
-M, --modprobe modprobe_program
Specify the path to the modprobe program. By default, iptables-save will inspect /proc/sys/kernel/modprobe to determine the exe-
cutable's path.
-c, --counters
include the current values of all packet and byte counters in the output
-t, --table tablename
restrict output to only one table. If not specified, output includes all available tables.
BUGS
None known as of iptables-1.2.1 release
AUTHORS
Harald Welte <laforge@gnumonks.org>
Rusty Russell <rusty@rustcorp.com.au>
Andras Kis-Szabo <kisza@sch.bme.hu> contributed ip6tables-save.
SEE ALSO iptables-apply(8),iptables-restore(8), iptables(8)
The iptables-HOWTO, which details more iptables usage, the NAT-HOWTO, which details NAT, and the netfilter-hacking-HOWTO which details the
internals.
iptables 1.6.1IPTABLES-SAVE(8)