Sponsored Content
Full Discussion: VPN IPSec Openswan
Special Forums IP Networking VPN IPSec Openswan Post 302909177 by ivancd on Tuesday 15th of July 2014 06:11:24 AM
Old 07-15-2014
VPN IPSec Openswan

Hi all,

I have installed Openswan and configured IPSec and works perfect, but for some unknown reasons it stop working. I see that the tunnels are up and established. The route to the destination are added. Everything by the book seems to be ok. But somehow when i start to ping the other side ( private ip ) the packet for that tunnel trying to go out from the interface that have public ip. And for the other tunnel they are not going anyway. All this is on a linux machine CentOS, with eth0 - public ip address, eth0:0 and eth0:1 are private for the tunnels. Can someone help me out here because i need this thing to work ( it's a production ) and i have lost a whole week.

Thanks in advanced !
 

9 More Discussions You Might Find Interesting

1. Cybersecurity

IPSec - VPN using shared key

Hello! I have some trouble trying to configure a VPN with two gateways. One of them uses IPSec with a single key, 256bits length, specified in /etc/ipsec.secrets. As FreeSwan manual page says, if i put esp=3des-md5-96, will be used a "64bit IV key (internally generated), a 192bit 3des ekey and a... (3 Replies)
Discussion started by: eNTer
3 Replies

2. IP Networking

IPSec VPN Routing

Hello, I'm trying to setup a gateway VPN between two routers across an unsecured network between two local networks. The routers are both linux and I'm using the ipsec tools, racoon and setkey. So far hosts from either local net can successfully ping hosts on the other local net without issue. ... (0 Replies)
Discussion started by: salukibob
0 Replies

3. BSD

Problem on IPSec

Hi, this is my first post...:p Hello Admin :) Can I have an ask for something with my configuration ? I have finished some kind of the tutorial to build ipsec site to site, and the "step" has finished completely. I have a simulation with a local design topology with two PC's (FreeBSD ... (0 Replies)
Discussion started by: aulia
0 Replies

4. UNIX for Advanced & Expert Users

Ipsec implementation

How can i implement Ipsec between two machines in linux_ ubuntu? any link?? suggestion?? (0 Replies)
Discussion started by: elinaz
0 Replies

5. Cybersecurity

IPSEC

hello, after configuration ipsec in ip4 I can not ping between client and server whereas I had success ping before configuration! I also generate different key for AH and ESP as i have shown below. what is my problem and what should i do to have ping and test the configuration? code: ... (0 Replies)
Discussion started by: elinaz
0 Replies

6. AIX

Allow port range using IPsec?

Hi Guys, Please could you tell me if it is possible to have a single rule/filter to allow a certain port range instead of a separate rule for each port? I'm sure it must be possible but I am unable to find the syntax. Thanks Chris (4 Replies)
Discussion started by: chrisstevens
4 Replies

7. IP Networking

IPSec Openswan Site to Site VPN - Big Pain

Hi @all, I try to connect 2 LANs with IPSec/Openswan LAN 1: 192.168.0.0/24 LAN 2: 192.168.1.0/24 This is my Config: conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies

8. IP Networking

Openswan with Cisco ASA

Hi all, I need this as soon as possible to solve it or at least to find out what is the problem. I have configured IPSec tunnels with Openswan and Cisco ASA, i have established a connection and the ping was fine, but after some time there is request time out from both sites. I don't have ASA... (0 Replies)
Discussion started by: ivancd
0 Replies

9. IP Networking

Best tool to monitor VPN IPSEC Tunneling

We are using cyberoam device, VPN IPSEC tunnel is going of frequently even the traffic is throug. Please suggest what may be the cause for the above mentioned issue. Also suggest a best tool to monitor the same VPN IPSEC tunnel connectivity. (4 Replies)
Discussion started by: marunmeera
4 Replies
Mirror/redirect action in tc(8)                                        Linux                                       Mirror/redirect action in tc(8)

NAME
mirred - mirror/redirect action SYNOPSIS
tc ... action mirred DIRECTION ACTION [ index INDEX ] dev DEVICENAME DIRECTION := { ingress | egress } ACTION := { mirror | redirect } DESCRIPTION
The mirred action allows packet mirroring (copying) or redirecting (stealing) the packet it receives. Mirroring is what is sometimes referred to as Switch Port Analyzer (SPAN) and is commonly used to analyze and/or debug flows. OPTIONS
ingress egress Specify the direction in which the packet shall appear on the destination interface. mirror redirect Define whether the packet should be copied (mirror) or moved (redirect) to the destination interface. index INDEX Assign a unique ID to this action instead of letting the kernel choose one automatically. INDEX is a 32bit unsigned integer greater than zero. dev DEVICENAME Specify the network interface to redirect or mirror to. EXAMPLES
Limit ingress bandwidth on eth0 to 1mbit/s, redirect exceeding traffic to lo for debugging purposes: # tc qdisc add dev eth0 handle ffff: ingress # tc filter add dev eth0 parent ffff: u32 match u32 0 0 action police rate 1mbit burst 100k conform-exceed pipe action mirred egress redirect dev lo Mirror all incoming ICMP packets on eth0 to a dummy interface for examination with e.g. tcpdump: # ip link add dummy0 type dummy # ip link set dummy0 up # tc qdisc add dev eth0 handle ffff: ingress # tc filter add dev eth0 parent ffff: protocol ip u32 match ip protocol 1 0xff action mirred egress mirror dev dummy0 Using an ifb interface, it is possible to send ingress traffic through an instance of sfq: # modprobe ifb # ip link set ifb0 up # tc qdisc add dev ifb0 root sfq # tc qdisc add dev eth0 handle ffff: ingress # tc filter add dev eth0 parent ffff: u32 match u32 0 0 action mirred egress redirect dev ifb0 SEE ALSO
tc(8), tc-u32(8) iproute2 11 Jan 2015 Mirror/redirect action in tc(8)
All times are GMT -4. The time now is 08:46 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy