07-10-2014
you cannot check physical SEA interface from the LPAR. LPAR itself cannot see if the SEA (VIOS) interface does (not) have a link.
Only the way is using ping test to the default gateway ... it something what even ehterchannel relies on client LPARs
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
Discussion started by: mono673
1 Replies
2. Solaris
I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper.
I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
Discussion started by: tubbyrana
2 Replies
3. Solaris
hi all,
How to install onboard ethernet card on Sun SPARC M4000 server? (3 Replies)
Discussion started by: Tlg13team
3 Replies
4. AIX
Hi,
In our AIX 5.2 server , we have one unused ethernet adapter which doesn't have cable connection . For this interface , we are getting alerts in errpt .
Could you suggesthow to stop this alert ? And sametime i would like to keep this device in ODM .
Is there... (1 Reply)
Discussion started by: sekarsamy
1 Replies
5. AIX
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Discussion started by: johnf
1 Replies
6. Red Hat
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Discussion started by: chidhu.anu
4 Replies
7. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
8. Hardware
Hi,
Does anybody have a "Sun 10-Gigabit Ethernet Adapter installation CD" or driver ixge for Sun 10-Gigabit Ethernet PCI-X adapter? I need it but can't find it anywhere. So if you know where I can download it or purchase it, please let me know. (Already tried Oracle's website, don't have it) ... (5 Replies)
Discussion started by: Lhao
5 Replies
9. Solaris
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Discussion started by: bentech4u
4 Replies
10. Red Hat
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
ping(8) System Manager's Manual ping(8)
Name
ping - send ICMP ECHO_REQUEST packets to network hosts
Syntax
/etc/ping [ options ] host [ datasize [ npackets ]]
Description
The DARPA Internet is a large and complex network of hardware connected together by gateways. The command utilizes the ICMP protocol's
mandatory ECHO_REQUEST datagram to elicit an ICMP ECHO_RESPONSE from a host or gateway. ECHO_REQUEST datagrams (pings) have an IP and ICMP
header, followed by a struct timeval, and then an arbitrary number of pad bytes used to fill out the packet. The length of the default
datagram 64 bytes, but this may be changed using the command-line option.
Typing ``ping host'' without any options will either report ``host is alive'' or ``no answer from host''. To get more statistics use the
-l option or one of the other options.
When using for fault isolation, it should first be run on the local host to verify that the local network interface is up and running.
Then, hosts and gateways further and further away should be pinged. The command with options sends one datagram per second and prints one
line of output for every ECHO_RESPONSE returned. No output is produced if there is no response. If an optional npackets is given, only
that number of requests is sent. Round-trip times and packet loss statistics are computed. When all responses have been received or the
program times out with npackets specified, or if the program is terminated with a SIGINT, a brief summary is displayed.
Options
-d Turns on SO_DEBUG flag on the socket.
-l Gives more statistics than if is used without options. Long output.
-r Bypasses the normal routing tables and sends directly to a host on an attached network. If the host is not on a directly-attached
network, an error is returned. This option can be used to ping a local host through an interface that has no route through it. For
example, after the interface was dropped by
-v Lists ICMP packets other than ECHO RESPONSE that are received. Verbose output.
Restrictions
This program is intended for use in network testing, measurement, and management. It should be used primarily for manual fault isolation.
Because of the load it could impose on the network, it is unwise to use during normal operations or from automated scripts.
See Also
netstat(1), ifconfig(8c)
ping(8)