I would say you have an extra PCI card with two network interfaces in your system.
Check the device pathes to your NICs in /etc/path_to_inst and see if one of the onboard devices is e1000g2. Here is a list of the onboard NIC device path:
I need to configure the iLOM for x4600 server. before I can set the IP details and commit, I need to set network state should be enabled. However my firmware is already the latest and I need not upgrade. I am not able to set the /SP/network state to enable. pls assist. i BELIEVE the bug was fixed... (5 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Hi Folks,
Has anyone seen these errors on bootup.
Mar 15 12:22:30 svc.startd: svc:/system/device/local:default: Method "/lib/svc/method/devices-local" failed due to signal SEGV.ht (c) 1983, 2010,
Oracle and/or its affiliates. All rights reserved.
Configuring devices. ... (1 Reply)
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
I got a replacement Heatsink and Fan unit, but the OEM unit has the SUN Thermal Interface Material (TIM) already on the heatsink matting surface. Because mine is used it does not have the TIM. Also there are 2 different TIM material SUN used based on the Processor (1-1.28GHz uses a glue backed... (1 Reply)
Booting and checking BIOS there is no option to enable-disable hyperthreading.
I have 8 Dual-Core AMD Opteron(tm) Processor 8220 and I see 16 cores.
Enable hyperthreading I should have 32 cores.
I have red hat 5.4 installed.
Anyone know how can enable hypethreading ? I have last BIOS/Firmware... (2 Replies)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT OSF1
sys_attrs_pci
sys_attrs_pci(5) File Formats Manual sys_attrs_pci(5)NAME
sys_attrs_pci - pci subsystem attributes
DESCRIPTION
This reference page lists and describes attributes for the PCI (pci) kernel subsystem. Refer to the sys_attrs(5) reference page for an
introduction to the topic of kernel subsystem attributes.
For this subsytem, users should modify only the following attribute and do so only for the purpose described. Any other visible attributes
cannot or should not be modified.
A bit-mask setting that allows the developer of PCI hardware and softwareto determine the PCI configuration parameters on an Alpha
system based on the PCI bus. By setting PCI_Developer_Debug to different values, a variety of hardware-related or software-related
information about all PCI devices on an AlphaServer are printed out at system bootstrap time. If loadable drivers are used, loadable
configuration data is also printed out on execution of the sysconfig -c command.
Refer to the /usr/include/io/dec/pci/pci_debug.h file for valid bit-field settings for this attribute. The pci_debug.h file con-
tains macro definitions that state the type of information that is printed out if PCI_Developer_Debug is set to a particular value.
Any combination of the bit-flags is valid. For example, the value 0x70 allows the hardware or software developer to see the PCI
configuration header information that the kernel reads or assigns to PCI devices.
Default value: 0
Minimum value: 0
Maximum value: FFFFFFFF(16)SEE ALSO sys_attrs(5)
Writing PCI Bus Device Drivers
sys_attrs_pci(5)