Powerha on AIX 6.1.9 Post: 302908314

10 More Discussions You Might Find Interesting

1. AIX

Oracle and SAP on AIX 6.1 + PowerHA resources ?

I was wondering if any one have any guides or documention regarding Oracle and SAP on AIX 6.1 + PowerHA setups in one guide step by step Thanks

2. AIX

PowerHA - assistant can't find network

I've configured multiple clusters using PowerHA 5.5, but never using the 'Two-node cluster configuration assistant'. I removed all the clusters, clean setup, and gave the assistant a try. I've filled in all the necessary options: Communication Path to Takeover Node Application Server ...

3. AIX

PowerHA, same subnet for persistent and service ip

I am new in AIX and please forgive my poor english. I know that AIX allow same subnet IPs for different interfaces, which result in multipath routing / route striping. My question is, is there any best practice for the persistent and service IP with same subnet to stay on same interface, or...

4. AIX

PowerHA Disk on VIO Server

Hello AIX GURU's Can anybody tell me the steps to crate shared VG (enhanced concurent) for my Lpars from VIO server? my questions are: 1. Should I crate Enhanced Concurent VG in VIO and map it using virtual Scsi to Lpar? or 2. Can I just create virtual SCSI in VIO and map to Lpar and...

5. AIX

PowerHA with 3rd node for communication

Looking to find PowerHA with 3rd node used for communication (voting node) only. Does anyone use such configuration with IBM products?

6. AIX

PowerHA HACMP on VIOS servers

Few questions regarding Power HA ( previously known as HACMP) and VIOS POWERVM IVM ( IBM Virtualization I/O Server ) Is it possible to create HACMP cluster between two VIOS servers Physical Machine_1 VIOS_SERVER_1 LPAR_1 SHARED_DISK_XX VIOS_SERVER_2 Physical Machine_2 LPAR_2...

7. AIX

PowerHA 5.5.0.4 on AIX 5.3 TL10 upgrade question

Hi all, I want to upgrade a clustered AIX 5.3 TL10 with PowerHA 5.5.0.4. To both AIX 6.1 and PowerHA 6.1 in an wasy way. Any guidelines or procedures in an easy way to accomplish this task safely? Note : fdown time is an acceptable option.

8. AIX

VXVM in POWERHA 6.1

I have created a VxVM disk group in AIX7.1. I have tried to added this VxVM disk group in powerHA 6.1. But in cluster VxVM DGs are not listing. Is there any other procedure to add vxvm diskgroup to hacmp. Please share me steps for adding vxvm diskgroup to hacmp.

9. AIX

PowerHa 7.1 Migration check failed

Hello Guys, I was trying to upgrade the PowerHA from 6.1.0.9 to 7.1.3 in prod cluster. Have snapshot migration and run climgcheck. 1. Run climgcheck on node1(kul1pqcmur01) and it success 2. Upgrade the cluster sw 3. Run climgcheck on node2(kul1pqcmur02) and it failed with below errors ...

10. AIX

Upgrading PowerHA from 7.1.0 to 7.1.3

Hi All, As per the IBM upgrade/support matrix IBM Techdocs Technote: PowerHA for AIX Version Compatibility Matrix we can't do online upgrade or rolling migration from powerha v7.1.0 to v7.1.3. on AIX61_TL9_SP4, So we are following the steps as below ... 1 ) Bring down the cluster 2 )...

LEARN ABOUT CENTOS

iprupdate

IPRUPDATE(8)						      System Manager's Manual						      IPRUPDATE(8)

NAME

       iprupdate - IBM Power RAID adapter/device microcode update utility

SYNOPSIS

       iprupdate

       iprupdate --debug --check_only --daemon --use-polling --use-uevents

DESCRIPTION

       iprupdate  is used to update the microcode on IBM storage adapters and the disk units attached to them to a minimum supported level. It can
       be run at any time while the ipr device driver is loaded. The utility will check the microcode revision level of each storage  adapter/disk
       unit  on  the  system  and  compare  it	to  the  microcode  revision  level  that  is installed in /etc/microcode, /usr/lib/microcode, and
       /lib/firmware.  If the microcode level on the adapter/device is below the minimum supported level and the level	of  the  latest  image	is
       newer, the microcode will be updated to the latest level available. It is desired that this be called in the boot process.

OPTIONS

       --version
	      Print the version number of iprupdate

       --debug
	      Enable additional error logging. Enabling this will result in additional errors logging to /var/log/messages.

       --check_only
	      Check if any adapters or disk units are below their minimum supported level.

       --daemon
	      Run as a daemon to handle adapters and devices being hotplugged.

       --use-polling
	      Do not use netlink/uevent notification, but rather poll for adapter and device configuration changes.

       --use-uevents
	      Use  netlink/uevent notification rather than polling for adapter and device configuration changes. If not specified, polling will be
	      used until the first uevent notification appears, then netlink will be used.

AUTHOR

       Brian King (brking@us.ibm.com)

								   February 2005						      IPRUPDATE(8)