Hello and thanks in advance.
I have a Sun box with raid 1 on the O/S disks using solaris svm.
I want to unmirror my swap partition, and add the slice on the second disk as an additional swap device. This would give me twice as much swap space.
I have been warned not to do this by some... (3 Replies)
Dear Guyz:)
I have 2 different input files like this. I would like to pick the values or letters from the inputfile2 based on inputfile1 keys (A,F,N,X,Z).
I have done similar task by using awk but in that case the inputfiles are similar like in inputfile2 (all keys in 1st column and values in... (16 Replies)
free -m : 1023 total swap space
created default partition /dev/sdb1 50M using fdisk. i did write the changes.
#mkswap /dev/sdb1
#swapon /dev/sdb1
free -m : 1078 total swap space
this shows that the swap is on
Question : i did not change the type LINUX SWAP (82) in fdisk.
so why is... (5 Replies)
Hi
I have an integrity machine rx7620 and rx8640 running hp-ux 11.31. I'm planning to fine tune the system:
- I would like to know when does the memory swap space spill over to the device swap space?
- And how much % of memory swap utilization should be specified (swap space device... (6 Replies)
hello friends,
i have written one perl script.Which opens a file and search for some parameter's value and gets the status of these parameters. but while i am trying to return these value always i am getting false. Can any one please help me..
here is that function:
=======================... (5 Replies)
- I have two files (File 1 and File 2) and the contents of the files are mentioned below.
- I am trying to compare the values of Column1 of File1 with Column1 of File2. If a match is found, print the corresponding value from Column2 of File1 in Column5 of File2.
- I tried to modify and use... (10 Replies)
Hello All,
I have a below data in a .csv file where all rows where col1 is A, col2 is odd numbers, similarly even numbers for all rows where col1 is B.
Note that my data has some other columns(not shown here) too (around 100) after col2.
Tool,Data
A,1
A,3
A,5
....
so on
B,2
B,4
.... ... (4 Replies)
I am trying to read a input file which has two columns separated by space
Input file
server1 server2
server3 server4
server5 server6
When i execute the below while code it reads line by line and a and b variables are able to successfully fetch the values
while read a b
do
echo "$a"
echo... (5 Replies)
Hi Solaris Folks :),
I need to calculate the swap usage on solaris server, please let me understand the output of below swap -s and swap -l commands.
$swap -s
total: 1774912k bytes allocated + 240616k reserved = 2015528k used, 14542512k available
$swap -l
swapfile dev swaplo... (6 Replies)
array=( 8 5 6 2 3 4 7 1 9 0 )
for i in "${array}"
do
echo $i
done
# i need the output like this by swapping of array values
0
9
1
7
4
3
2
6
5
8 (7 Replies)
Discussion started by: Meeran Rizvi
7 Replies
LEARN ABOUT DEBIAN
expect_unbuffer
UNBUFFER(1) General Commands Manual UNBUFFER(1)NAME
unbuffer - unbuffer output
SYNOPSIS
unbuffer program [ args ]
INTRODUCTION
unbuffer disables the output buffering that occurs when program output is redirected from non-interactive programs. For example, suppose
you are watching the output from a fifo by running it through od and then more.
od -c /tmp/fifo | more
You will not see anything until a full page of output has been produced.
You can disable this automatic buffering as follows:
unbuffer od -c /tmp/fifo | more
Normally, unbuffer does not read from stdin. This simplifies use of unbuffer in some situations. To use unbuffer in a pipeline, use the
-p flag. Example:
process1 | unbuffer -p process2 | process3
CAVEATS
unbuffer -p may appear to work incorrectly if a process feeding input to unbuffer exits. Consider:
process1 | unbuffer -p process2 | process3
If process1 exits, process2 may not yet have finished. It is impossible for unbuffer to know long to wait for process2 and process2 may
not ever finish, for example, if it is a filter. For expediency, unbuffer simply exits when it encounters an EOF from either its input or
process2.
In order to have a version of unbuffer that worked in all situations, an oracle would be necessary. If you want an application-specific
solution, workarounds or hand-coded Expect may be more suitable. For example, the following example shows how to allow grep to finish pro-
cessing when the cat before it finishes first. Using cat to feed grep would never require unbuffer in real life. It is merely a place-
holder for some imaginary process that may or may not finish. Similarly, the final cat at the end of the pipeline is also a placeholder
for another process.
$ cat /tmp/abcdef.log | grep abc | cat
abcdef
xxxabc defxxx
$ cat /tmp/abcdef.log | unbuffer grep abc | cat
$ (cat /tmp/abcdef.log ; sleep 1) | unbuffer grep abc | cat
abcdef
xxxabc defxxx
$
BUGS
The man page is longer than the program.
SEE ALSO
"Exploring Expect: A Tcl-Based Toolkit for Automating Interactive Programs" by Don Libes, O'Reilly and Associates, January 1995.
AUTHOR
Don Libes, National Institute of Standards and Technology
1 June 1994 UNBUFFER(1)