I have 2 VIO servers and a network connection to each of them in an etherchannel so running entstat against the individually adapters doesn't work.
I do see this info in the entstat output for the etherchannel. Since virtual adapters don't really have "links", I think the comparative is "LAN State":
I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper.
I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
Hi,
In our AIX 5.2 server , we have one unused ethernet adapter which doesn't have cable connection . For this interface , we are getting alerts in errpt .
Could you suggesthow to stop this alert ? And sametime i would like to keep this device in ODM .
Is there... (1 Reply)
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Hi,
Does anybody have a "Sun 10-Gigabit Ethernet Adapter installation CD" or driver ixge for Sun 10-Gigabit Ethernet PCI-X adapter? I need it but can't find it anywhere. So if you know where I can download it or purchase it, please let me know. (Already tried Oracle's website, don't have it) ... (5 Replies)
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
LEARN ABOUT FREEBSD
if_kue
KUE(4) BSD Kernel Interfaces Manual KUE(4)NAME
kue -- Kawasaki LSI KL5KUSB101B USB Ethernet driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device uhci
device ohci
device usb
device kue
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_kue_load="YES"
DESCRIPTION
The kue driver provides support for USB Ethernet adapters based on the Kawasaki LSI KL5KLUSB101B chipset.
The KL5KLUSB101B supports a 128-entry multicast filter, single perfect filter entry for the station address and promiscuous mode. Packets
are received and transmitted over separate USB bulk transfer endpoints.
The Kawasaki chipset supports only 10Mbps half-duplex mode, hence there are no ifmedia(4) modes to select.
For more information on configuring this device, see ifconfig(8).
HARDWARE
The kue driver supports Kawasaki LSI KL5KLUSB101B based USB Ethernet adapters including:
o 3Com 3c19250
o 3Com 3c460 HomeConnect Ethernet USB Adapter
o ADS Technologies USB-10BT
o AOX USB101
o ATen UC10T
o Abocom URE 450
o Corega USB-T
o D-Link DSB-650C
o Entrega NET-USB-E45, NET-HUB-3U1E
o I/O Data USB ETT
o Kawasaki DU-H3E
o LinkSys USB10T
o Netgear EA101
o Peracom USB Ethernet Adapter
o Psion Gold Port USB Ethernet adapter
o SMC 2102USB, 2104USB
DIAGNOSTICS
kue%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
transmission before a timeout expired.
kue%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring.
SEE ALSO arp(4), netintro(4), ng_ether(4), ifconfig(8)HISTORY
The kue device driver first appeared in FreeBSD 4.0.
AUTHORS
The kue driver was written by Bill Paul <wpaul@ee.columbia.edu>.
BUGS
The kue driver does not accumulate Ethernet collisions statistics because the Kawasaki firmware does not appear to maintain any internal sta-
tistics.
BSD October 7, 2006 BSD