How to check the ethernet status for vlan and lhea adapter in client servers?
Hi Techies,
I have a doubt.
In this server , I can check the link status for etherchannel like :
Similarly is there any way to check the link status of lhea and vlan adapters ??
Thanks & Regards,
Jayadeava
---------- Post updated at 12:34 AM ---------- Previous update was at 12:23 AM ----------
Also need to add that, I do not have access to the vio server. Hence wanted to know if there is any way to check the link status from the client machine itself.
Thanks in Advance.
Last edited by Don Cragun; 06-27-2014 at 07:05 PM..
Reason: Add CODE tags.
I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper.
I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
Hi,
In our AIX 5.2 server , we have one unused ethernet adapter which doesn't have cable connection . For this interface , we are getting alerts in errpt .
Could you suggesthow to stop this alert ? And sametime i would like to keep this device in ODM .
Is there... (1 Reply)
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Hi,
Does anybody have a "Sun 10-Gigabit Ethernet Adapter installation CD" or driver ixge for Sun 10-Gigabit Ethernet PCI-X adapter? I need it but can't find it anywhere. So if you know where I can download it or purchase it, please let me know. (Already tried Oracle's website, don't have it) ... (5 Replies)
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
LEARN ABOUT DEBIAN
ovs-vlan-test
ovs-vlan-test(1) Open vSwitch Manual ovs-vlan-test(1)NAME
ovs-vlan-test - check Linux drivers for problems with vlan traffic
SYNOPSIS
ovs-vlan-test [-s | --server] control_ip vlan_ip
Common options:
[-h | --help] [-V | --version]
DESCRIPTION
The ovs-vlan-test utility has some limitations, for example, it does not use TCP in its tests. Also it does not take into account MTU to
detect potential edge cases. To overcome those limitations a new tool was developed - ovs-test. ovs-test is currently supported only on
Debian so, if possible try to use that on instead of ovs-vlan-test.
The ovs-vlan-test program may be used to check for problems sending 802.1Q traffic which may occur when running Open vSwitch. These prob-
lems can occur when Open vSwitch is used to send 802.1Q traffic through physical interfaces running certain drivers of certain Linux kernel
versions. To run a test, configure Open vSwitch to tag traffic originating from vlan_ip and forward it out the target interface. Then run
the ovs-vlan-test in client mode connecting to an ovs-vlan-test server. ovs-vlan-test will display "OK" if it did not detect problems.
Some examples of the types of problems that may be encountered are:
o When NICs use VLAN stripping on receive they must pass a pointer to a vlan_group when reporting the stripped tag to the networking
core. If no vlan_group is in use then some drivers just drop the extracted tag. Drivers are supposed to only enable stripping if a
vlan_group is registered but not all of them do that.
o On receive, some drivers handle priority tagged packets specially and don't pass the tag onto the network stack at all, so Open
vSwitch never has a chance to see it.
o Some drivers size their receive buffers based on whether a vlan_group is enabled, meaning that a maximum size packet with a VLAN tag
will not fit if no vlan_group is configured.
o On transmit, some drivers expect that VLAN acceleration will be used if it is available, which can only be done if a vlan_group is
configured. In these cases, the driver may fail to parse the packet and correctly setup checksum offloading or TSO.
Client Mode
An ovs-vlan-test client may be run on a host to check for VLAN connectivity problems. The client must be able to establish HTTP connec-
tions with an ovs-vlan-test server located at the specified control_ip address. UDP traffic sourced at vlan_ip should be tagged and
directed out the interface whose connectivity is being tested.
Server Mode
To conduct tests, an ovs-vlan-test server must be running on a host known not to have VLAN connectivity problems. The server must have a
control_ip on a non-VLAN network which clients can establish connectivity with. It must also have a vlan_ip address on a VLAN network
which clients will use to test their VLAN connectivity. Multiple clients may test against a single ovs-vlan-test server concurrently.
OPTIONS -s, --server
Run in server mode.
-h, --help
Prints a brief help message to the console.
-V, --version
Prints version information to the console.
EXAMPLES
Display the Linux kernel version and driver of eth1.
uname -r
ethtool -i eth1
Set up a bridge which forwards traffic originating from 1.2.3.4 out eth1 with VLAN tag 10.
ovs-vsctl -- add-br vlan-br
-- add-port vlan-br eth1
-- add-port vlan-br vlan-br-tag tag=10
-- set Interface vlan-br-tag type=internal
ifconfig vlan-br-tag up 1.2.3.4
Run an ovs-vlan-test server listening for client control traffic on 172.16.0.142 port 8080 and VLAN traffic on the default port of 1.2.3.3.
ovs-vlan-test -s 172.16.0.142:8080 1.2.3.3
Run an ovs-vlan-test client with a control server located at 172.16.0.142 port 8080 and a local VLAN ip of 1.2.3.4.
ovs-vlan-test 172.16.0.142:8080 1.2.3.4
SEE ALSO
ovs-vswitchd(8), ovs-ofctl(8), ovs-vsctl(8), ovs-test(8), ethtool(8), uname(1)Open vSwitch December 2010 ovs-vlan-test(1)