STEP 1
# Set variable
FILE=/tmp/mainfile
SEARCHFILE =/tmp/searchfile
# THIS IS THE MAIN FILE.
cat /tmp/mainfile
Interface Ethernet0/0 "outside", is up, line protocol is up
Hardware is i82546GB rev03, BW 100 Mbps
Full-Duplex(Full-duplex), 100 Mbps(100 Mbps)
MAC address... (6 Replies)
I am using the while-loop to read a file.
The file has lines with null-terminated strings (words, actually.)
What I have by that reading - just a first word up to '\0'!
I need to have whole string up to 'new line' - (LF, 10#10, 16#A)
What I am doing wrong?
#make file 'grb' with... (6 Replies)
Hi
Trying to do like this :
echo "$variable1\n $(cat file.txt)"
but it only adds one time. When I run this cmd again with different variable it only replaces line of variable1.
How to add constantly line into first line in file ? (3 Replies)
Hi ,
I am trying to write an shell, which reads a text file (from a location) having a list of numbers of strictly 5 digits only ex: 33144
Now my script will check :
1) that each entry is only 5 digits & numeric only, no alphabets, & its not empty.
2)then it executes a shell script called... (8 Replies)
Hello, I am quite new in shell scripting and I would like to write a little scritp to run a program on some parameters files.
all my parameters files are in the same directory, so pick them up with
ls *.para >>dirafter that I have a dir file like that:
param1.para
param2.para
etc...
I... (2 Replies)
Hi All,
I'm trying to figure out which are the trusted-ips and which are not using a script file.. I have a file named 'ip-list.txt' which contains some ip addresses and another file named 'trusted-ip-list.txt' which also contains some ip addresses. I want to read a line from... (4 Replies)
Hi all,
I have a log file say Test.log that gets updated continuously and it has data in pipe separated format. A sample log file would look like:
<date1>|<data1>|<url1>|<result1>
<date2>|<data2>|<url2>|<result2>
<date3>|<data3>|<url3>|<result3>
<date4>|<data4>|<url4>|<result4>
What I... (3 Replies)
I have a file
file_name_O.txt
The file can have different number of other files names or nothing
I will check
cnt=`wc -l file_name_0.txt`
if ;then
exit 1
fi
Now I have to start checking file names, i.e. read txt file line by line. If amount of ,lines equal 1, I can... (4 Replies)
line(1) General Commands Manual line(1)NAME
line - read one line from user input
SYNOPSIS
timeout]
DESCRIPTION
copies one line (up to a new-line) from the standard input and writes it on the standard output. It returns an exit code of 1 on EOF and
always prints at least a new-line. It is often used within shell files to read from the user's terminal.
Options
recognizes the following command-line option:
Timeout after
timeout seconds where timeout is an integer value (if a non-integer value is specified, it is converted to an integer;
i.e., rounded down). A blank is required between and the timeout argument. This option is not documented in POSIX and
other industry standards, and should not be used in portable applications.
EXTERNAL INFLUENCES
International Code Set Support
Single- and multi-byte character code sets are supported.
EXAMPLES
The following lines in a shell script prompt for a file name and display information about the file:
To limit the response time to 10 seconds, use the form:
then test for no response. If no response occurs before timeout expires, a default behavior should be provided.
WARNINGS
This command is likely to be withdrawn from X/Open standards. Applications using this command might not be portable to other vendors' sys-
tems. As an alternative is recommended.
SEE ALSO sh(1), read(2).
STANDARDS CONFORMANCE line(1)