06-26-2014
What Solaris version exactly?
(Network interfaces are handled very differently in Solaris 11 compared to Solaris 10).
8 More Discussions You Might Find Interesting
1. IP Networking
Hi, Anybody who worked with IPv6 on Solaris 8.
I want to get rid of IPv6 (Uninstall).
Any comments ...ideas...will be highly appreciated. (4 Replies)
Discussion started by: s_aamir
4 Replies
2. IP Networking
Hello guyz..
did some of u have implement or making a testbed for IPv6?
if yes, can u attached the procedures and standard guidelines because i really need for my proposal..
thanx.. (2 Replies)
Discussion started by: unknown2205
2 Replies
3. Linux
I am trying to capture the ipv6 packets through pcap utility.
For that i am redirecting the ipv6 packets to the loopback address , but the ipv6 packets are not getting redirected to tha loopback address.Instead they are taking there normal routes. (1 Reply)
Discussion started by: vikasmca05
1 Replies
4. Red Hat
Hello,
I was wondering if it would be possible to run two VMs one with services for IPv4 and the other one with services for IPv6. The main physical system would be connected to a IPv6 switch.
I think it should be fine but I would like to hear out your comments. (1 Reply)
Discussion started by: svalenciatech
1 Replies
5. HP-UX
my problem: i want to change from ipv4 to ipv6 on my home network.
On hpux i can assign only address non routable as fe80::1 fe80::3 etc to my lan0
Editing netconf-ipv6 i can assing a routable ipv6 address like
fd55:282f:3b98::/48
or
2001:470:26:307:89a0:aba1:f98b:eb3e
but only to alias... (0 Replies)
Discussion started by: Linusolaradm1
0 Replies
6. UNIX for Dummies Questions & Answers
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
7. IP Networking
I am trying to setup an IPv6 network.
I modified the interfaces file:
/etc/network/interfaces
# The loopback network interface
auto lo
iface lo inet loopback
iface etho0 inet static
address 2620:7:a000::1
netmask 64
gateway ::ffff:c0a8:101
... (0 Replies)
Discussion started by: Meow613
0 Replies
8. Solaris
Hello Dears ,
please I need your support I have Oracle Solaris 10 X86 server please if you can advise how can I add IP v6 on my server and if IPv6 was disabled how can i enable it also how can i add two IP (v4 and v6) on the same interface or I have to add another interface .
Thanks in... (1 Reply)
Discussion started by: ttashman
1 Replies
LEARN ABOUT OPENSOLARIS
lx
lx(5) Standards, Environments, and Macros lx(5)
NAME
lx - Linux branded zone
DESCRIPTION
The lx brand uses the branded zones framework described in brands(5) to enable Linux binary applications to run unmodified on a machine
with a Solaris Operating System kernel.
The lx brand includes the tools necessary to install a CentOS 3.x or Red Hat Enterprise Linux 3.x distribution inside a non-global zone.
The brand supports the execution of 32-bit Linux applications on x86/x64 machines running the Solaris system in either 32-bit or 64-bit
mode.
Supported Linux Distributions
The lx brand emulates the system call interfaces provided by the Linux 2.4.21 kernel, as modified by Red Hat in the RHEL 3.x distributions.
This kernel provides the system call interfaces consumed by the glibc version 2.3.2 released by Red Hat.
In addition, the lx brand partially emulates the Linux /dev and /proc interfaces.
Configuration and Administration
The lx brand supports the whole root non-global zone model. All of the required linux packages are installed into the private file systems
of the zone.
The zonecfg(1M) utility is used to configure an lx branded zone. Once a branded zone has been installed, that zone's brand cannot be
changed or removed. The zoneadm(1M) utility is used to report the zone's brand type and administer the zone. The zlogin(1) utility is used
to log in to the zone.
Application Support
The lx zone only supports user-level Linux applications. You cannot use Linux device drivers, Linux kernel modules, or Linux file systems
from inside an lx zone.
You cannot add any non-standard Solaris devices to a Linux zone. Any attempt to do so will result in a zone that zonecfg(1M) will refuse to
verify.
You cannot run Solaris applications inside an lx zone. Solaris debugging tools such as DTrace (see dtrace(1M)) and mdb (see mdb(1)) can be
applied to Linux processes executing inside the zone, but the tools themselves must be running in the global zone. Any core files generated
are produced in the Solaris format, and such files can only be debugged with Solaris tools.
ATTRIBUTES
See attributes(5) for a description of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWlxr, SUNWlxu |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO
mdb(1), zlogin(1), zonename(1), dtrace(1M), zoneadm(1M), zonecfg(1M), brands(5), zones(5), lx_systrace(7D)
SunOS 5.11 19 Sep 2006 lx(5)