Hey Folks,
I have a file that contains data that I am working with, sometimes this file has a very long string of text that messes with an awk command in a script i am trying to build. I would like to cut this string of text out of a file and then redirect everything except that string to a new... (5 Replies)
Hi, I'm trying to output all text from the first paragraph in a file that contains a specific string through the last paragraph in that file that contains that string.
Previously, I was outputting just each paragraph with that search string with:
cat in_file | nawk '{RS=""; FS="\n";... (2 Replies)
Hi,
I have the following text file:
8 T1mapping_flip02 ok 128 108 30 1 665000-000008-000001.dcm
9 T1mapping_flip05 ok 128 108 30 1 665000-000009-000001.dcm
10 T1mapping_flip10 ok 128 108 30 1 665000-000010-000001.dcm
11 T1mapping_flip15 ok 128 108 30... (2 Replies)
I have text file as follows and would like to remove the last occurance of "UNION ALL" string and replace @@ with single quote (').
Input text in file is
with temp as (
( select ----------- where OPERATION = @@B@@ and OBJECTTYPE = @@P@@ and start_time desc ) UNION ALL
( select... (9 Replies)
Hi,
I have log file which rolls out every second which is as this.
HttpGenRequest - -<!--OXi dbPublish--> <created="2014-03-24 23:45:37" lastMsgId="" requestTime="0.0333"> <response request="getOutcomeDetails" code="114" message="Request found no matching data" debug="" provider="undefined"/>... (3 Replies)
Hi
This is my first post and I'm just a beginner. So please be nice to me.
I have a couple of html files where a pattern beginning with "http://www.site.com" and ending with "/resource.dat" is present on every 241st line. How do I extract this to a new text file?
I have tried sed -n 241,241p... (13 Replies)
Hi,
I have a file(input.txt) and trying to format as output.txt. See the attached file format.
Note: This is a windows file (DOS format) and the commands are also going to execute on windows.
Basically I am trying to capture all the data in between Local Group Memberships and Global Group... (10 Replies)
I am trying to use awk to change a specific string in a field, if it is found, to another value. In the tab-delimited file the text in bold in $3 contains the string 23, which is always right before a ., if it is present.
I am trying to change that string to X, keeping the formatting and the... (3 Replies)
What I need is to remove the text from Location_file.txt from each line matching all entries from Remove_location.txt
Location_file.txt
FlowPrePaid, h3nmg1cm2,Jamaica_MTAImageFileFlowPrePaid,h0nmg1cm1, Flow_BeatTest,FlowRockTest
FlowNewTest,FlowNewTest,h0nmg1cm1
PartiallySubscribed,... (3 Replies)
Discussion started by: ketanraut
3 Replies
LEARN ABOUT FREEBSD
nos-tun
NOS-TUN(8) BSD System Manager's Manual NOS-TUN(8)NAME
nos-tun -- implement ``nos'' or ``ka9q'' style IP over IP tunnel
SYNOPSIS
nos-tun -t tunnel -s source -d destination -p protocol_number [source] target
DESCRIPTION
The nos-tun utility is used to establish an nos style tunnel, (also known as ka9q or IP-IP tunnel) using a tun(4) kernel interface.
Tunnel is the name of the tunnel device /dev/tun0 for example.
Source and destination are the addresses used on the tunnel device. If you configure the tunnel against a cisco router, use a netmask of
``255.255.255.252'' on the cisco. This is because the tunnel is a point-to-point interface in the FreeBSD end, a concept cisco does not
really implement.
Protocol number sets tunnel mode. Original KA9Q NOS uses 94 but many people use 4 on the worldwide backbone of ampr.org.
Target is the address of the remote tunnel device, this must match the source address set on the remote end.
EXAMPLES
This end, a FreeBSD box on address 192.168.59.34:
nos-tun -t /dev/tun0 -s 192.168.61.1 -d 192.168.61.2 192.168.56.45
Remote cisco on address 192.168.56.45:
interface tunnel 0
ip address 192.168.61.2 255.255.255.252
tunnel mode nos
tunnel destination 192.168.59.34
tunnel source 192.168.56.45
AUTHORS
Nickolay N. Dudorov <nnd@itfs.nsk.su> wrote the program, Poul-Henning Kamp <phk@FreeBSD.org> wrote the man-page. Isao SEKI
<iseki@gongon.com> added a new flag, IP protocol number.
BUGS
We do not allow for setting our source address for multihomed machines.
BSD April 11, 1998 BSD