Hi,
Since last week our server become too slow when we try to run application on it. When we run top command, it show as below:
So it's nothing to do with heavy utilization, right? Can you give some opinion on what actually had happended?
Thank you very much... :b: (4 Replies)
I have data file with customer.dat, and this contains the customer names
>cat customer.dat
FirstName1 LastName1
FistName2 LastName1
FistName3 MiddleName3 LastName3
This file can contain areoun 100 customer names.
Regards, (1 Reply)
Hi,
I have an excel file that have a random count of columns/fields and what im trying to do is to only retrieve all the rows under 2 specific field headers.
I can use the usually command for awk which is awk 'print{ $1 $2}' > output.txt, but the location of the 2 specific field headers is... (9 Replies)
Hello,
I am using Redhat redhat 4 update 4 kernal 2.6. My server is some time suddenly running slow.
The averge cpu load goes up to 50 to 60. (There is only two CPU and usually, the averge load
is between 1 to 2.5) That time, i see, there are several sessions connected.
Normally, we have... (5 Replies)
I need to find all the files that have group Read or Write permission or files that have user write permission.
This is what I have so far:
find . -exec ls -l {} \; | awk '/-...rw..w./ {print $1 " " $3 " " $4 " " $9}'
It shows me all files where group read = true, group write = true... (5 Replies)
Hi,
We have smb client running on two of the linux boxes and smb server on another linux system. During a backup operation which uses smb, read of a file was allowed while write to the same file was going on.Also simultaneous writes to the same file were allowed.Following are the settings in the... (1 Reply)
Dear All,
I have a hard disk in solaris on which the write performanc is too slow.
The CPU , RAM memory are absolutely fine.
What might be reason.
Kindly explain.
Rj (9 Replies)
There is a big problem with the server (VPS based on OpenVZ, CentOS 5, 3GB RAM). The problem is the following. The first 15-20 minutes after starting the server is operating normally, the load average is less than or about 1.0, but then begins to increase sharply% wa, then hovers around 95-99%.... (2 Replies)
Discussion started by: draiphod
2 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)