Help with to check the tcp network connectivity between servers and hosts
ello,
i am new to the networking side.
I have a requirement to check the tcp network connectivity between server it's running on and the list of host's and ports combination.
please help me where i am going wrong.
my code:
Code:
#!/bin/bash
#read the file line by line
cd "$1"
cat testping.txt | while read line
do
# check if there are no blank lines
if [ ! -z $line ]; then
hosts=${line//:/ }
echo $(nc -z $hosts) >> testouput.txt
fi
done
i think nc doesn't work, as i need to check the tcp connectivity.
Hi All,
I need an automation script to check the connectivity between 2 UNIX servers.
Could anybody please help in this regards?
regards,
janardhan (1 Reply)
We have two servers A and B (both running Solaris 10) out of which one is application server and the other is database server. The two servers faced certain network issues and the two servers were temporarily disconnected.this happened around 5AM GMT monday.Can anyone suggest some log files or... (2 Replies)
HI I have made a connection with external server which is also UNIX. I was tryign connectivity with this by telnet which fails and ping i sshowing socket is alive and traceroute tells the asterisk astersik:traceroute to 153.88.182.28 (153.88.182.28), 30 hops max, 8080 byte packets
1 * * *
2 *... (1 Reply)
hi all
just installed the netsec.options.tcpwrapper from expansion pack, which used to be a rpm, for my aix 6.1 test box.
it is so unpredictable. i set up the hosts.deny as suggested for all and allow the sshd for specific ip addresses/hostnames.
the tcpdchk says the hosts allowed and... (0 Replies)
Hi All
I am having issues using ftp between a solaris 10 server to a HP-UX 11.31 server, but from the solaris server to the hp-ux I am able to ping. This is what I have done so far:
in the solaris server:
root@MPCRS01 # svcs -a | grep ftp
online Jul_26 svc:/network/ftp:default... (12 Replies)
Hello,
I have a requirement to check the tcp network connectivity between server it's running on and the list of host's and ports combination.
i have written the below code but it doesn't work, but when i execute the nc command outside the script it works fine.
please help me where i am... (8 Replies)
Newbie with UNIX here.
Currently troubleshooting a UNIX terminal we have.
I determined it to be bad and swapped it out with a known good terminal. I went in and changed the IP address and host name to reflect the old terminal. Although now there is no connectivity.
I swapped out the NIC... (1 Reply)
Hi everyone!
Some time ago, I had to check connectivity with a big list of hosts, using different formats (protocol://server:port/path/, server:port, ....).
I developed a script that checks the connectivity using different commands (ping, telnet, nc, curl).
It worked for me so I'm sharing it... (9 Replies)
I am trying to establish passwordless connectivity between server A and server B, but unsuccessfuly, because I beleive two issues.
the first one is that on both servers, it is not possible to use root to login, it only allows to connect using a user (any) them su - root, which in turns I am able... (1 Reply)
Discussion started by: fretagi
1 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)