Hi,
Since last week our server become too slow when we try to run application on it. When we run top command, it show as below:
So it's nothing to do with heavy utilization, right? Can you give some opinion on what actually had happended?
Thank you very much... :b: (4 Replies)
I have data file with customer.dat, and this contains the customer names
>cat customer.dat
FirstName1 LastName1
FistName2 LastName1
FistName3 MiddleName3 LastName3
This file can contain areoun 100 customer names.
Regards, (1 Reply)
Hi,
I have an excel file that have a random count of columns/fields and what im trying to do is to only retrieve all the rows under 2 specific field headers.
I can use the usually command for awk which is awk 'print{ $1 $2}' > output.txt, but the location of the 2 specific field headers is... (9 Replies)
Hello,
I am using Redhat redhat 4 update 4 kernal 2.6. My server is some time suddenly running slow.
The averge cpu load goes up to 50 to 60. (There is only two CPU and usually, the averge load
is between 1 to 2.5) That time, i see, there are several sessions connected.
Normally, we have... (5 Replies)
I need to find all the files that have group Read or Write permission or files that have user write permission.
This is what I have so far:
find . -exec ls -l {} \; | awk '/-...rw..w./ {print $1 " " $3 " " $4 " " $9}'
It shows me all files where group read = true, group write = true... (5 Replies)
Hi,
We have smb client running on two of the linux boxes and smb server on another linux system. During a backup operation which uses smb, read of a file was allowed while write to the same file was going on.Also simultaneous writes to the same file were allowed.Following are the settings in the... (1 Reply)
Dear All,
I have a hard disk in solaris on which the write performanc is too slow.
The CPU , RAM memory are absolutely fine.
What might be reason.
Kindly explain.
Rj (9 Replies)
There is a big problem with the server (VPS based on OpenVZ, CentOS 5, 3GB RAM). The problem is the following. The first 15-20 minutes after starting the server is operating normally, the load average is less than or about 1.0, but then begins to increase sharply% wa, then hovers around 95-99%.... (2 Replies)
Discussion started by: draiphod
2 Replies
LEARN ABOUT OSF1
volreattach
volreattach(8) System Manager's Manual volreattach(8)NAME
volreattach - Reattaches disk drives that have once again become accessible
SYNOPSIS
/usr/sbin/volreattach [-rb] [accessname...]
/usr/sbin/volreattach -c accessname
OPTIONS
The volreattach utility has the following options: Calls the volrecover utility to attempt to recover stale plexes of any volumes on the
failed disk. Performs the reattach operation in the background. Checks whether a reattach is possible. No operation is performed, but the
name of the disk group and disk media name at which the disk can be reattached is displayed.
DESCRIPTION
The volreattach utility attempts to reattach disks using the same disk group and media names they had before detachment.
This operation may be necessary if a disk has a transient failure, or if some disk drivers are unloaded or unloadable when the Logical
Storage Manager is started, causing disks to enter the failed state.
If the problem is fixed, the volreattach command can be used to reattach the disks without plexes being flagged as stale, as long as the
reattach happens before any volumes on the disk are started.
The volreattach command is called from the voldiskadm menus as part of disk recovery.
The volreattach utility tries to find a disk with a disk group and disk ID matching that of the disk(s) being reattached. If the matching
disk is found, the reattach operation may still fail if the original cause (or some other cause) for the disk failure still exists.
EXIT CODES
A zero exit status is returned if it is possible to perform a reattach. Otherwise, non-zero is returned.
SEE ALSO volintro(8), voldiskadm(8), volrecover(8)volreattach(8)