I am mirroring a single partition drive with raidctl. The source partition was mounted when I created the mirror with raidctl -c c1t1d0 c1t3d0. The source disk was defined with s2 and s6 only.
I didn't think to umount it first.
Is there a problem with that? (2 Replies)
I have two 72GB disks that are mirrored and mounted (/backup). I have a 18GB drive in an array I just attached to the server, which is running Solaris 9.
I need to create a new logical volume partition and make the existing mirror device (/dev/md/dsk/d34) and the array's 18GB drive a member of... (3 Replies)
I've looked a little but haven't found a solid answer, assuming there is one.
What's better, hardware mirroring or ZFS mirroring? Common practice for us was to use the raid controllers on the Sun x86 servers. Now we've been using ZFS mirroring since U6. Any performance difference? Any other... (3 Replies)
Hi ,
I am new to SVM .when i try to learn RAID 1 , first they are creating two RAID 0 strips through
metainit d51 1 1 c0t0d0s2
metainit d52 1 1 c1t0d0s2
In the next step
metainit d50 -m d51
d50: Mirror is setup
next step is
metaattach d50 d52
d50 : submirror d52 is... (7 Replies)
I’m setting up a boot disk mirror on Solaris 10 x86. I’m used to doing it on SPARC, where you can copy the partition table using fmthard. My x86 boot disk has 2 primary partitions, a Solaris one and a diagnostic one. Is there a way to copy those 2 primary partitions to the second disk without... (6 Replies)
OK, I upgraded to the latest version of Solaris 10. Perhaps 'upgrade' isn't the right term because I reinstalled the root/boot drive with Solaris 10. Prior to this I had 4 physical drives. The first two had "/" and "/usr", the other two had a /var/audit and /home. I initially booted from cdrom and... (7 Replies)
what is the difference between DRD and Root Mirror Disk using LVM mirror ? (3 Replies)
Discussion started by: maxim42
3 Replies
LEARN ABOUT DEBIAN
pull-debian-source
PULL-DEBIAN-SOURCE(1) General Commands Manual PULL-DEBIAN-SOURCE(1)NAME
pull-debian-source - download and extract a source package from Debian
SYNOPSIS
pull-debian-source [options] <source package> [release|version]
DESCRIPTION
pull-debian-source downloads and extracts the specified version of source package, or the latest version in the specified Debian release.
pull-debian-source will try the preferred mirror, default mirror, security mirror, and fall back to Launchpad or snapshot.debian.org, in
search of the requested version.
OPTIONS
source package
The source package to download from Debian.
release
The release to download the source package from. Defaults to unstable.
version
The specific version of the package to download.
-d, --download-only
Do not extract the source package.
-m DEBIAN_MIRROR, --mirror=DEBIAN_MIRROR
Use the specified mirror. Should be in the form http://ftp.debian.org/debian. If the package isn't found on this mirror,
pull-debian-source will fall back to the default mirror.
-s DEBSEC_MIRROR, --security-mirror=DEBSEC_MIRROR
Use the specified mirror. Should be in the form http://security.debian.org. If the package isn't found on this mirror,
pull-debian-source will fall back to the default mirror.
--no-conf
Do not read any configuration files, or configuration from environment variables.
-h, --help
Display the usage instructions and exit.
ENVIRONMENT
All of the CONFIGURATION VARIABLES below are also supported as environment variables. Variables in the environment take precedence to
those in configuration files.
CONFIGURATION VARIABLES
The following variables can be set in the environment or in ubuntu-dev-tools(5) configuration files. In each case, the script-specific
variable takes precedence over the package-wide variable.
PULL_DEBIAN_SOURCE_DEBIAN_MIRROR, UBUNTUTOOLS_DEBIAN_MIRROR
The default value for --mirror.
PULL_DEBIAN_SOURCE_DEBSEC_MIRROR, UBUNTUTOOLS_DEBSEC_MIRROR
The default value for --security-mirror.
SEE ALSO dget(1), pull-debian-debdiff(1), pull-lp-source(1), ubuntu-dev-tools(5)ubuntu-dev-tools 22 January 2011 PULL-DEBIAN-SOURCE(1)