Hi ,
I have one system installed on Linux Red Hat 3.0. I have ip of system 3.156.168.*** and i want to ping some port that is on this IP which command i can do this?
sam70 (1 Reply)
Hi All,
Need your help one more time.
I am trying to ping a linux machine which is not responding to ping.
However traceroute can reach the machine and I can log in to it by ssh. I have checked /proc/sys/net/ipv4/icmp_echo_ignore_all it is already set as "0".
It is not happening in the... (1 Reply)
I have an old MP-Ras Unix system. I have setup netowkring but am unable to ping any local network pcs or the default gateway. If i use the arp -a command I receive the correct mac address for all connected pcs but I cannot ping anything except the local address. Any help would be appreciative.
... (7 Replies)
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
I am unable to ping my remote server.My server is unable to ping the same. both are able to ping the gateway. both the ip's are on same network.i use a proxy tunnel on my remote server.Help if any clues. (6 Replies)
SHAME, that's all that I'm felling right now, however I'm not finding PING or either tracert in my box (Solaris 10).
1) Yes my PATH does have /usr/bin /usr/sbin
# echo $PATH
/opt/csw:/usr/bin:/sbin:/usr/sbin:/usr/ccs/bin:/usr/sfw/bin:/opt/csw/bin:/opt/csw/gcc2/bin:/opt/csw/bin
2) If I... (1 Reply)
Hi
I am using perl to ping a list of nodes - with script below :
$p = Net::Ping->new("icmp");
if ($p->ping($host,1)){
print "$host is alive.\n";
}
else {
print "$host is unreacheable.\n";
}
$p->close();... (4 Replies)
This is a small program as a tester for a basic sweep generator for bandwidth testing of AudioScope.sh.
This DEMO is only capable of 4KHz down to about 85Hz and back due to the low bit rate, but it is proof of concept for a much wider variant using a much higher bit rate.
The file generated... (4 Replies)
help with bash script!
im am working on this script to make sure my server will stay online, so i made this script..
HOSTS="192.168.138.155"
COUNT=4
pingtest(){
for myhost in "$@"
do
ping -c "$COUNT" "$myhost" &&return 1
done
return 0
}
if pingtest $HOSTS
#100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
LEARN ABOUT MOJAVE
echo
ECHO(1) BSD General Commands Manual ECHO(1)NAME
echo -- write arguments to the standard output
SYNOPSIS
echo [-n] [string ...]
DESCRIPTION
The echo utility writes any specified operands, separated by single blank (' ') characters and followed by a newline ('
') character, to the
standard output.
The following option is available:
-n Do not print the trailing newline character. This may also be achieved by appending 'c' to the end of the string, as is done by iBCS2
compatible systems. Note that this option as well as the effect of 'c' are implementation-defined in IEEE Std 1003.1-2001
(``POSIX.1'') as amended by Cor. 1-2002. Applications aiming for maximum portability are strongly encouraged to use printf(1) to sup-
press the newline character.
Some shells may provide a builtin echo command which is similar or identical to this utility. Most notably, the builtin echo in sh(1) does
not accept the -n option. Consult the builtin(1) manual page.
EXIT STATUS
The echo utility exits 0 on success, and >0 if an error occurs.
SEE ALSO builtin(1), csh(1), printf(1), sh(1)STANDARDS
The echo utility conforms to IEEE Std 1003.1-2001 (``POSIX.1'') as amended by Cor. 1-2002.
BSD April 12, 2003 BSD