05-14-2014
it is data ent out of a instrument. sends out binary packets. i jus want to be aboe to read them.
8 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
i purchased, what was labeled as a 4-port fast ethernet sbus card from ebay.
i installed it in my ultra1, and it seems to be working fine. how can i determine if the card is infact a fast ethernet card vs. the standard ethernet 4-port card? (7 Replies)
Discussion started by: xyyz
7 Replies
2. UNIX for Dummies Questions & Answers
hi. Im trying to install a switch.
And the manual says i should type a command including a SerialPortDevicePath. which is the filepath to serial port used for connection.
However.. nothing about how to find this info.
Could anyone help me where to find this path?
thx
mr.T (6 Replies)
Discussion started by: tyskertøs
6 Replies
3. Solaris
Hi Friends,
I am using intel system installed solaris 10, when i check ifconfig -a it doesn't show any thing eg-for HP servers hme0, for sun servers-iprb0. for me it doesn't show any thing, and tell me what files to be modified. Thanks in Advance. (1 Reply)
Discussion started by: kurva
1 Replies
4. Solaris
I have a new Sun 440 and I am trying to configure it. Non of the Ethernet ports are enabled; when I issue "ifconfig -a" it returns nothing. Is there a way to know the available port name (e.g. ce, bge, etc.) by running a command or so ? (4 Replies)
Discussion started by: StarSol
4 Replies
5. Linux
Sir,
Do linux have device file for ethernet card. Can I use open , read , write , system calls to read data transferred through LAN. Is there any methods to read network datas (with out header and tailor information).
Hope anyone can help me out. Thanking you....
... (5 Replies)
Discussion started by: iamjayanth
5 Replies
6. Red Hat
I have a RAC setup that was configured before I started at my new company. I would like to reconfigure the network devices and change the names. How complex is this regarding the Oracle RAC environment? Does the Oracle RAC rely on the device name or is it only relying on the IP information?
... (1 Reply)
Discussion started by: s ladd
1 Replies
7. Red Hat
Hi All,
Could anyone please help to resolve the below problem.
I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error.
I spent 2 days for the above and go through with several suggestion found by googling. But no luck.
... (0 Replies)
Discussion started by: Tanmoy
0 Replies
8. UNIX for Advanced & Expert Users
Currently I am using this laborious command
lvdisplay | awk '/LV Path/ {p=$3} /LV Name/ {n=$3} /VG Name/ {v=$3} /Block device/ {d=$3; sub(".*:", "/dev/dm-", d); printf "%s\t%s\t%s\n", p, "/dev/mapper/"v"-"n, d}'
Would like to know if there is any shorter method to get this mapping of... (2 Replies)
Discussion started by: royalibrahim
2 Replies
KUE(4) BSD Kernel Interfaces Manual KUE(4)
NAME
kue -- Kawasaki LSI KL5KUSB101B USB Ethernet driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device uhci
device ohci
device usb
device kue
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_kue_load="YES"
DESCRIPTION
The kue driver provides support for USB Ethernet adapters based on the Kawasaki LSI KL5KLUSB101B chipset.
The KL5KLUSB101B supports a 128-entry multicast filter, single perfect filter entry for the station address and promiscuous mode. Packets
are received and transmitted over separate USB bulk transfer endpoints.
The Kawasaki chipset supports only 10Mbps half-duplex mode, hence there are no ifmedia(4) modes to select.
For more information on configuring this device, see ifconfig(8).
HARDWARE
The kue driver supports Kawasaki LSI KL5KLUSB101B based USB Ethernet adapters including:
o 3Com 3c19250
o 3Com 3c460 HomeConnect Ethernet USB Adapter
o ADS Technologies USB-10BT
o AOX USB101
o ATen UC10T
o Abocom URE 450
o Corega USB-T
o D-Link DSB-650C
o Entrega NET-USB-E45, NET-HUB-3U1E
o I/O Data USB ETT
o Kawasaki DU-H3E
o LinkSys USB10T
o Netgear EA101
o Peracom USB Ethernet Adapter
o Psion Gold Port USB Ethernet adapter
o SMC 2102USB, 2104USB
DIAGNOSTICS
kue%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
transmission before a timeout expired.
kue%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring.
SEE ALSO
arp(4), netintro(4), ng_ether(4), ifconfig(8)
HISTORY
The kue device driver first appeared in FreeBSD 4.0.
AUTHORS
The kue driver was written by Bill Paul <wpaul@ee.columbia.edu>.
BUGS
The kue driver does not accumulate Ethernet collisions statistics because the Kawasaki firmware does not appear to maintain any internal sta-
tistics.
BSD
October 7, 2006 BSD