sco unix 5.0.x, several weeks ago, I add a telnet-like service in inetd.conf, it runs well for 100 network terminals.
But nowdays, the terminals can connect to server successfully after booting machine, but several hours later, can not connect. "netstat -p tcp -a" can NOT find the port in... (1 Reply)
Discussion started by: shark_gao
1 Replies
2. Post Here to Contact Site Administrators and Moderators
Dear Administrators,
I think Mr. Vino is one of your Moderators here because he closes this thread: https://www.unix.com/showthread.php?p=302086230#post302086230
without a valid reason.
Rule 7 states no headhunters or recruiters, but career advice is not prohibited here i think, because it... (2 Replies)
Hi folks,
First of all, sorry about my english, isn't the best and thks for advance.
Here es my problem...
I have virtualize an SCO unix with VMware ESX 3 and everything was going on beatifull until that i try to connect from anorther host, i can't do it so i check the connection with... (5 Replies)
Hello,
Actually there are some bugs in application which does not close the TCP connection to other server though CORBA.
We need to kill that ESTABLISHED connections as new connection are not happeneing as the allocated ports were used and showing as ESTABLISHED
Is there any... (4 Replies)
Dear experts,
I am seeing a lot of TCP failed connection attempts from "netstat -s" on one of our servers.
How can I pin point what connection failed and what are the ports involved?
Any tools/commands I can dig in deeper to diag. what went wrong on these "failed connection attempts"?
... (2 Replies)
I've recently installed Solaris 10 10/9 in a new Dell Power Edge 630. Whenever I try to telnet, ssh, or FTP TO this box FROM another box on the same network segment, the following occurs:
Roughly 80% of the time I get "Unable to connect to remote host: Connection refused"
The remaining 20%... (0 Replies)
I have a TCPIP server application (a Vendor package) which by default allows 10 connections. It provides a parameter to allow us to increase the maximum allowable connections in case it is needed. Intermittently this application is failing with maximum number of connections reached even when there... (1 Reply)
Discussion started by: AIX_user
1 Replies
LEARN ABOUT PHP
inet_type
inet_type(4) File Formats inet_type(4)NAME
inet_type - default Internet protocol type
SYNOPSIS
/etc/default/inet_type
DESCRIPTION
The inet_type file defines the default IP protocol to use. Currently this file is only used by the ifconfig(1M) and netstat(1M) commands.
The inet_type file can contain a number of <variable>=<value> lines. Currently, the only variable defined is DEFAULT_IP, which can be
assigned a value of IP_VERSION4, IP_VERSION6, or BOTH.
The output displayed by the ifconfig and netstat commands can be controlled by the value of DEFAULT_IP set in inet_type file. By default,
both commands display the IPv4 and IPv6 information available on the system. The user can choose to suppress display of IPv6 information by
setting the value of DEFAULT_IP. The following shows the possible values for DEFAULT_IP and the resulting ifconfig and netstat output that
will be displayed:
IP_VERSION4 Displays only IPv4 related information. The output displayed is backward compatible with older versions of the ifconfig(1M)
and netstat(1M) commands.
IP_VERSION6 Displays both IPv4 and IPv6 related information for ifconfig and netstat.
BOTH Displays both IPv4 and IPv6 related information for ifconfig and netstat.
The command-line options to the ifconfig and netstat commands override the effect of DEFAULT_IP as set in the inet_type file. For example,
even if the value of DEFAULT_IP is IP_VERSION4, the command
example% ifconfig -a6
will display all IPv6 interfaces.
EXAMPLES
Example 1: Suppressing IPv6 Related Output
This is what the inet_type file must contain if you want to suppress IPv6 related output:
DEFAULT_IP=IP_VERSION4
SEE ALSO ifconfig(1M), netstat(1M)SunOS 5.10 16 Jun 1999 inet_type(4)