sco unix 5.0.x, several weeks ago, I add a telnet-like service in inetd.conf, it runs well for 100 network terminals.
But nowdays, the terminals can connect to server successfully after booting machine, but several hours later, can not connect. "netstat -p tcp -a" can NOT find the port in... (1 Reply)
Discussion started by: shark_gao
1 Replies
2. Post Here to Contact Site Administrators and Moderators
Dear Administrators,
I think Mr. Vino is one of your Moderators here because he closes this thread: https://www.unix.com/showthread.php?p=302086230#post302086230
without a valid reason.
Rule 7 states no headhunters or recruiters, but career advice is not prohibited here i think, because it... (2 Replies)
Hi folks,
First of all, sorry about my english, isn't the best and thks for advance.
Here es my problem...
I have virtualize an SCO unix with VMware ESX 3 and everything was going on beatifull until that i try to connect from anorther host, i can't do it so i check the connection with... (5 Replies)
Hello,
Actually there are some bugs in application which does not close the TCP connection to other server though CORBA.
We need to kill that ESTABLISHED connections as new connection are not happeneing as the allocated ports were used and showing as ESTABLISHED
Is there any... (4 Replies)
Dear experts,
I am seeing a lot of TCP failed connection attempts from "netstat -s" on one of our servers.
How can I pin point what connection failed and what are the ports involved?
Any tools/commands I can dig in deeper to diag. what went wrong on these "failed connection attempts"?
... (2 Replies)
I've recently installed Solaris 10 10/9 in a new Dell Power Edge 630. Whenever I try to telnet, ssh, or FTP TO this box FROM another box on the same network segment, the following occurs:
Roughly 80% of the time I get "Unable to connect to remote host: Connection refused"
The remaining 20%... (0 Replies)
I have a TCPIP server application (a Vendor package) which by default allows 10 connections. It provides a parameter to allow us to increase the maximum allowable connections in case it is needed. Intermittently this application is failing with maximum number of connections reached even when there... (1 Reply)
Discussion started by: AIX_user
1 Replies
LEARN ABOUT FREEBSD
tcpdrop
TCPDROP(8) BSD System Manager's Manual TCPDROP(8)NAME
tcpdrop -- drop TCP connections
SYNOPSIS
tcpdrop local-address local-port foreign-address foreign-port
tcpdrop [-l] -a
DESCRIPTION
The tcpdrop command may be used to drop TCP connections from the command line.
If -a is specified then tcpdrop will attempt to drop all active connections. The -l flag may be given to list the tcpdrop invocation to drop
all active connections one at a time.
If -a is not specified then only the connection between the given local address local-address, port local-port, and the foreign address
foreign-address, port foreign-port, will be dropped.
Addresses and ports may be specified by name or numeric value. Both IPv4 and IPv6 address formats are supported.
The addresses and ports may be separated by periods or colons instead of spaces.
EXIT STATUS
The tcpdrop utility exits 0 on success, and >0 if an error occurs.
EXAMPLES
If a connection to httpd(8) is causing congestion on a network link, one can drop the TCP session in charge:
# sockstat -c | grep httpd
www httpd 16525 3 tcp4
192.168.5.41:80 192.168.5.1:26747
The following command will drop the connection:
# tcpdrop 192.168.5.41 80 192.168.5.1 26747
The following command will drop all connections but those to or from port 22, the port used by sshd(8):
# tcpdrop -l -a | grep -vw 22 | sh
SEE ALSO netstat(1), sockstat(1)AUTHORS
Markus Friedl <markus@openbsd.org>
Juli Mallett <jmallett@FreeBSD.org>
BSD January 30, 2013 BSD