04-29-2014
ifconfig and route and the like aren't going to make any permanent changes on any UNIX system I know.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
HELP!! How do you change the network setting from auto-duplex to 100 Base T Full Duplex in Red HaT? (1 Reply)
Discussion started by: johnlong
1 Replies
2. UNIX for Dummies Questions & Answers
Total newbie here!!
How do I view and alter network settings (ip address, subnet mask and default gateway) in UNIX?
Thanks in advance.. (3 Replies)
Discussion started by: ZappaDub
3 Replies
3. Linux
I've been looking for documentation on how to stop this behavior. I have two nics in my system.
eth0: configured manually and as a dhcp server for the local network
eth1: configured w/ dhcp enabled connected to router
dns server addresses keep getting reset every few minutes. i suspect... (0 Replies)
Discussion started by: rbetzen
0 Replies
4. Shell Programming and Scripting
say i have a system on thats on a network with access to the internet.
now, i have sensitive information on this system and i do not want the system to be connected to the outside world anymore. how do i get it off the network without actually having to disconnect the cables?
i'm asking this... (4 Replies)
Discussion started by: Terrible
4 Replies
5. Solaris
I have problem with network settings.
Where i can find network config ? I'm newbie, but i very want learn this OS.
I find :
/etc/hostname.<interface>
/etc/netconfig
/etc/netmasks
/etc/networks
/etc/inet/hosts
But where i can write my IP-address and after reboot i be know that my server... (2 Replies)
Discussion started by: jess_t03
2 Replies
6. HP-UX
Hello everyone..
While printing through command line, we can set printing option with -o <lanscape/portrait> to print file in required mode.
But i want to know is there any way we can set this as default behaviour for this printer?
After configuration any script we can modify for this... (0 Replies)
Discussion started by: laxmikant
0 Replies
7. UNIX for Dummies Questions & Answers
Hello Unix Gurus Who I Hope Reads This,
I have quasi-inherited control over a Linux cluster at a university research lab. The post-doc that set it up is gone, and the person in charge of administering the cluster doesn't know a ton about Linux. Amongst other things, I want to use the cluster... (0 Replies)
Discussion started by: mbl
0 Replies
8. Solaris
Hi
i have created a solaris zone but have not yet connected any network cables for this new zone,
can i set the zone up without running the command 'add net' and not adding an ip or physical interface?
i tried to add dummy internet settings and get this
zonecfg:coddr> add net... (4 Replies)
Discussion started by: newbiesolaris10
4 Replies
9. Shell Programming and Scripting
Hello, Newbie question on scripting - I'm looking to create a simple script that will work on RHEL5 that will adjust the network settings: ip address, default gateway, and subnet mask. If anything else needs to be done (service network stop / start) or should be done to make settings active - I... (4 Replies)
Discussion started by: rojizo
4 Replies
10. Fedora
Hello, I just installed Fedora 16 and wanted to add some apps to startup but realized System settings has only a small setup of utilities and does not have option for adding apps to startup. Also it's missing some other icons that I see on my Rhat 6.2 . I'm logged in as user from admin group but it... (2 Replies)
Discussion started by: susja
2 Replies
LEARN ABOUT DEBIAN
ecaccess-association-list
ECACCESS-ASSOCIATION-LIST(1p) User Contributed Perl Documentation ECACCESS-ASSOCIATION-LIST(1p)
NAME
ecaccess-association-list - List your ECtrans Associations
SYNOPSIS
ecaccess-association-list -version|-help|-manual
ecaccess-association-list [-debug] [-gateway name] [association-name]
DESCRIPTION
List all your ECtrans Associations. When an association-name is specified then the details for this Association is displayed.
ARGUMENTS
association-name (optional)
The name of the Association to retrieve the details.
OPTIONS
-gateway name
This is the name of the ECaccess Gateway where the Associations are installed. It is by default the Gateway you are connected to.
In order to get the name of your current Gateway you can use the ecaccess-gateway-name command. When using the commands at ECMWF
the default Gateway is always "ecaccess.ecmwf.int".
-version
Display version number and exits.
-help Print a brief help message and exits.
-manual Prints the manual page and exits.
-debug Display the SOAP messages exchanged.
EXAMPLES
ecaccess-association-list
List all your Associations on your default Gateway.
ecaccess-association-list -gateway ecaccess.ecmwf.int ginko
List the details of the Association ginko on the ecaccess.ecmwf.int Gateway.
SEE ALSO
ecaccess-association-delete, ecaccess-association-get, ecaccess-association-protocol, ecaccess-association-put and ecaccess.
perl v5.14.2 2012-04-16 ECACCESS-ASSOCIATION-LIST(1p)