I must remove hex characters 0A and 0D from several fields within an MS Access Table. Since I don't think it can be done in Access, I am trying here.
I am exporting a Table from Access (must be fixed length fields, I think, for my idea to work here) into a text format.
I then want to run a... (2 Replies)
Hi All,
I have huge xml file. The file contains some comment tags . I have requirement to replace comment tag with another comment tag.
Say for example : file X has -- Part of the file
<?xml version="1.0" encoding="ISO-2"?><translationResults jobDate="20070123 23:20:51"... (1 Reply)
I was wondering if somebody could help me with something on UNIX. I have a file that looks like this -
"nelson,bill","bill","123 Main St","Mpls","MN",55444,8877,william
I want to replace all comma with pipes (|), except if the comma is within double quotes. (The first field is an example of... (8 Replies)
Hello all,
This is my first post here, so please excuse me if this question is too obvious or has been asked before. I am new to Unix and although I tried to search your forum for the answer to my question, I could not find an answer that would help me.
I have a 500MB csv file with numeric values... (1 Reply)
Hi there!
I'm new in this and probably is a quite simple task but I still cannot manage to do it:
I have to read some files line by line and then change the input format into another one, but the very first step is to replace the empty variables by error values. I mean, each line looks like:... (2 Replies)
Hello All,
I have a requirement where I need to replaced the hex character - '\x0D' with 2 hex characters - 'x0D' & 'x0A'
I am trying to use SED -
But somehow its not working. Any pointers?
Also the hex character '\x0D' can occur anywhere in the line.
Can this also be accomplished... (6 Replies)
I have the following file consisting of dates and sample measurements:
05��Oct��2010 1.31��
06��Oct��2010 1.32��
07��Oct��2010 1.31��
The hex characters are \xc2\xa0 in sequence.
I have tried to remove the characters as follows:
sed -i '' -e 's/\xc2\xa0//g' file.dat
and as follows... (6 Replies)
Suppose I have a file which has 1000 columns (5 SHOWN FOR EXAMPLE)
two alphabets are separated by a space and then tab
A A"\t"C C"\t"G G"\t"0 0"\t"T T
A G"\t"C C"\t"G G"\t"A T"\t"0 0
G A"\t"0 0"\t"G C"\t"A A"\t"T C
whenever there is a 0 0 in any column, the output should be printed as
A... (12 Replies)
Discussion started by: rossi
12 Replies
LEARN ABOUT MOJAVE
cat
CAT(1) BSD General Commands Manual CAT(1)NAME
cat -- concatenate and print files
SYNOPSIS
cat [-benstuv] [file ...]
DESCRIPTION
The cat utility reads files sequentially, writing them to the standard output. The file operands are processed in command-line order. If
file is a single dash ('-') or absent, cat reads from the standard input. If file is a UNIX domain socket, cat connects to it and then reads
it until EOF. This complements the UNIX domain binding capability available in inetd(8).
The options are as follows:
-b Number the non-blank output lines, starting at 1.
-e Display non-printing characters (see the -v option), and display a dollar sign ('$') at the end of each line.
-n Number the output lines, starting at 1.
-s Squeeze multiple adjacent empty lines, causing the output to be single spaced.
-t Display non-printing characters (see the -v option), and display tab characters as '^I'.
-u Disable output buffering.
-v Display non-printing characters so they are visible. Control characters print as '^X' for control-X; the delete character (octal
0177) prints as '^?'. Non-ASCII characters (with the high bit set) are printed as 'M-' (for meta) followed by the character for the
low 7 bits.
EXIT STATUS
The cat utility exits 0 on success, and >0 if an error occurs.
EXAMPLES
The command:
cat file1
will print the contents of file1 to the standard output.
The command:
cat file1 file2 > file3
will sequentially print the contents of file1 and file2 to the file file3, truncating file3 if it already exists. See the manual page for
your shell (i.e., sh(1)) for more information on redirection.
The command:
cat file1 - file2 - file3
will print the contents of file1, print data it receives from the standard input until it receives an EOF ('^D') character, print the con-
tents of file2, read and output contents of the standard input again, then finally output the contents of file3. Note that if the standard
input referred to a file, the second dash on the command-line would have no effect, since the entire contents of the file would have already
been read and printed by cat when it encountered the first '-' operand.
SEE ALSO head(1), more(1), pr(1), sh(1), tail(1), vis(1), zcat(1), setbuf(3)
Rob Pike, "UNIX Style, or cat -v Considered Harmful", USENIX Summer Conference Proceedings, 1983.
STANDARDS
The cat utility is compliant with the IEEE Std 1003.2-1992 (``POSIX.2'') specification.
The flags [-benstv] are extensions to the specification.
HISTORY
A cat utility appeared in Version 1 AT&T UNIX. Dennis Ritchie designed and wrote the first man page. It appears to have been cat(1).
BUGS
Because of the shell language mechanism used to perform output redirection, the command ``cat file1 file2 > file1'' will cause the original
data in file1 to be destroyed!
The cat utility does not recognize multibyte characters when the -t or -v option is in effect.
BSD March 21, 2004 BSD