03-14-2014
Maybe I don't understand network settings completely:
In HMC's network settings currently there are two adapters with next :
-eth0 (assuming direct connection to FSP) , Private, Autodetection, enabled DHCP server (192.168.128.2-192.168.255.254), greyed out settings for IPv4 (192.168.128.1)
-eth1 (assuming management port), Open, Autodetection, DHCP disabled, IPv4 192.168.1.121, 255.255.255.0.
Routing settings: Default Gateway 192.168.1.1 for eth1
No tagging involved.
VIOS and LPAR;s are on same subnet as eth1.
Now I figured that default gateway has to be the same one that of VIOS and LPAR's are using in order for HMC to connect to them via console.
You are right that IP settings for eth1 does not matter but than I can not reach remotely HMC unless I change route, which in turn makes problem for HMC accessing LPAR's via console.
Now I tried attaching cable to eth2 and connecting it to new subnet, added static NET route 192.168.1.0, 192.168.50.1, 255.255.255.0 for eth2 and everything works fine (192.168.50.1 is new subnet gateway). I can remotely access HMC and still HMC can access LPAR's via console.
So my question now is if you missconfigure IP settings on VIOS how can I access missconfigured system or better question how you can access VIOS that does not have network interface? e.g. in KVM I do not care about network settings at all as long as I have physical access to hypervisor (I can access guests via console).
Thanks
10 More Discussions You Might Find Interesting
1. AIX
Hello guys,
It would be so nice of you if someone can provide me with these informations.
1) My SAN group assigned 51G of LUN space to the VIO server.I ran cfgdev to discover the newly added LUN. Unfortunately most of the disks that are in VIO server is 51G. How would I know which is the newly... (3 Replies)
Discussion started by: solaix14
3 Replies
2. AIX
I created a profile in HMC for a new LPAR and activated it but not yet installed AIX.
Is there a step to make this new LPAR available as vhostX from the VIO server after creating and activating an HMC profile?
I already shared the CD-ROM device from the HMC profile.
Thanks.
-... (1 Reply)
Discussion started by: learner1
1 Replies
3. AIX
Hello,
I have created mapping of 2 virtual adapters for Lpars using following command:
mkvdev -vdev ipanalyzerlv1 -vadapter vhost11
mkvdev -vdev ipanalyzerlv -vadapter vhost13
The above two commands were succesfull
but when I want to map the third virtual device to the same Lpar than... (3 Replies)
Discussion started by: Vit0_Corleone
3 Replies
4. AIX
Hi All,
Besides the licenses on VIO and LPAR. What's the main difference with the two? I have installed VIO, my manager told me so, because it's like a free hypervisor but I never installed LPAR before. How do you install it? And if you can give more info on the two, that would be great.
... (5 Replies)
Discussion started by: itik
5 Replies
5. AIX
Hi All,
i would like to know if it's possible to know all the IP Addresses of all LPAR's interfaces from HMC (without connect into LPAR).
And if i can know also the "Application" hostname of LPAR from HMC.
Thanks in advance.
Bye
Mario (2 Replies)
Discussion started by: Zio Bill
2 Replies
6. AIX
Hi guys,
does anyone know how to get a list of the LPAR running on VIOS?
Thanks! (5 Replies)
Discussion started by: cecco16
5 Replies
7. AIX
I am trying to install AIX 5.3 on one of the LPARs through VIOS but I get this error 0518
Reference Code Selection
0518 (Time stamp: 12/18/12 12:10:20 AM UTC)
Starting kernel (Time stamp: 12/18/12 12:10:15 AM UTC)
AIX is starting. (Time stamp: 12/18/12 12:10:15 AM... (10 Replies)
Discussion started by: filosophizer
10 Replies
8. AIX
Does anyone know of a command that can be run on the lpar to show the name of the lpars managing HMC?
We have a large environment and records a little old on which HMC manages which lpars....if i could login to an lpar and just issue a command to show me its managing hmc that would be great. (2 Replies)
Discussion started by: Foiled
2 Replies
9. UNIX for Beginners Questions & Answers
We want to integrate powervm by using openstack with hmc.
Now we encounter problem with the console, we can open the terminal within hmc, and I think hmc using tech java applet.
sample applet code like
<applet codebase="https://172.16.28.174/hmc/"... (0 Replies)
Discussion started by: eagle
0 Replies
10. AIX
hello
P6 was managed by HMC, tried to install on it VIOS 2.2.6
and got this error message
Hosting requires a hosting partition -- boot not permitted
vios-4 - imgbb.com
then after creating an lpar in HMC got this message
B2001230
vios-3 - imgbb.com
anyone know how to solve this... (3 Replies)
Discussion started by: filosophizer
3 Replies
LEARN ABOUT DEBIAN
pbuilder-uml.conf
pbuilder-uml.conf(5) pbuilder pbuilder-uml.conf(5)
NAME
pbuilder-uml.conf - configuration file for user-mode-linux port of pbuilder
DESCRIPTION
/etc/pbuilder/pbuilder-uml.conf contains default values used in pbuilder-user-mode-linux program invocation.
FORMAT
MY_ETH0=tuntap,,,192.168.0.2
Configures ethernet setting used for booting linux. See how rootstrap boots your system, and copy that.
Specify --eth0=slirp,12345,/usr/bin/slirp-fullbolt to use the slirp connection.
UML_IP=192.168.0.3
IP address to use for guest OS.
This can be set to dhcp for obtaining IP address through DHCP.
UML_NETMASK=255.255.255.0
Guest OS netmask
UML_NETWORK=192.168.0.0
Guest OS network
UML_BROADCAST=255.255.255.255
Guest OS broadcast
UML_GATEWAY=192.168.0.1
Guest OS gateway
PBUILDER_UML_IMAGE=${HOME}/uml-image
Guest OS file system image.
UML_MOUNT_TMPFS=no
Whether to mount tmpfs inside the guest image. This is probably mostly useless.
BUILDPLACE=${HOME}/tmp/
The location which build will take place. pbuilder-user-mode-linux will place temporary COW files to there. The user running UML
needs to be able to access that directory.
UML_MEM=128
The amount of memory allowed for UML. Give more value to here.
UML_HOSTNAME=uml-host
The hostname for the UML.
The hostname should be available in /etc/hosts so that hostname -f will be able to return the FQDN.
UML_BUILDRESULT=/directory/of/build/result
The directory where build result of pbuilder-user-mode-linux is stored.
ROOTSTRAP_IMAGESIZE=size-in-megabytes
The size, in MB, of the disk iamge to create. Defaults to 1000.
NOTES
It is advised to set APTCACHEHARDLINK to no in ~/.pbuilderrc. see pbuilderrc(5) for details.
AUTHOR
Initial coding, and main maintenance is done by Junichi Uekawa <dancer@debian.org>.
The homepage is available at http://pbuilder.alioth.debian.org
FILES
/etc/pbuilder/pbuilder-uml.conf, ${HOME}/.pbuilderrc
SEE ALSO
/usr/share/doc/pbuilder/pbuilder-doc.html, pbuilder-user-mode-linux(1), pbuilder(8), pbuilderrc(5), pdebuild(1)
Debian 2003 Jan 8 pbuilder-uml.conf(5)