Sponsored Content
Operating Systems AIX Install AIX lpar via hmc, can't access cd drive Post 302892534 by ibmtech on Thursday 13th of March 2014 10:25:07 AM
Old 03-13-2014
Have you assigned the CD-ROM drive to the LPAR,
From the HMC, have you assigned the RAID controller (which as CD ROM) to the LPAR(atleast as desired)?
If you have not done so, assign the RAID Controller.
You can refer the manual provided by your Vendor, or if you don't have it, physically go to Data Center and determine which CEC has CD ROM attached to it. Note down the CEC No and search for RAID Controller with that SLOT NO.

Also, in SMS, list all the available resources for boot (I thinks its option no 7, like DISK, Ethernet and CD ROM). At the time of selecting boot option.

Hope this helps.
 

10 More Discussions You Might Find Interesting

1. AIX

How to install a DAT drive on AIX.

Hello, we are trying to install an HP DAT drive on an IBM AIX RS6000 server. We have attached the SCSI connection and power cylced the unit, but still cannot see the device in smit. I am only a couple months into AIX, so I am very green! The server we are working on is in a lab environment,... (2 Replies)
Discussion started by: dayinthelife
2 Replies

2. AIX

CDROM Issue on LPAR HMC VIO

Whenever I assign/unassign a CDROM ( RAID CTRL ) to Active LPAR from HMC, I have to reboot the LPAR. How can I do it without rebooting the LPARS. POWER6 with HMC LPARS = AIX 6.1 Any info developerWorks : AIX and UNIX : PowerVM Forum : Moving CD-ROM/DVD-ROM dynamically ... But... (5 Replies)
Discussion started by: filosophizer
5 Replies

3. AIX

How to mksysb to a tape drive connected to a different LPAR?

I have 2 LPARs running AIX 5.3. Both are on the same VLAN. One LPAR, which I'll call LPAR2, has a 4mm SCSI tape drive connected to it, while LPAR1 does not have a tape drive connected. I am able to take mksysb backups of LPAR2 to the tape drive since it's directly connected. However, I need to... (2 Replies)
Discussion started by: need2bageek
2 Replies

4. AIX

Discovery LPAR from HMC

Hi All, i would like to know if it's possible to know all the IP Addresses of all LPAR's interfaces from HMC (without connect into LPAR). And if i can know also the "Application" hostname of LPAR from HMC. Thanks in advance. Bye Mario (2 Replies)
Discussion started by: Zio Bill
2 Replies

5. AIX

Setup hacmp on lpar with a hmc for home lab

Unix Guys i want to setup a lab in my house for learning, i want to setup and hacmp and a seperate server where i can setup 2 lpars and then cluster those 2 lpars and setup them up for failover what is the cheapest way to achive this. my objective is to learn hmc -> managed server via... (7 Replies)
Discussion started by: asyed123
7 Replies

6. AIX

Command to show HMC of this lpar?

Does anyone know of a command that can be run on the lpar to show the name of the lpars managing HMC? We have a large environment and records a little old on which HMC manages which lpars....if i could login to an lpar and just issue a command to show me its managing hmc that would be great. (2 Replies)
Discussion started by: Foiled
2 Replies

7. AIX

Moving VIOS, LPAR's, HMC to different subnet

Hi, Just joined to new company with one Power 720 Express (8202-E4C) server and have no much experience with IBM systems. I am trying to move everything I mentioned to different subnet as required by customer contract (currently sitting on same subnet as company lan). Access to this subnet will... (8 Replies)
Discussion started by: spricer
8 Replies

8. AIX

Install AIX , do i need hmc console

Hi, For installing aix on power series , do i need to install hmc first? or i can connect hmc after? Rgs, (7 Replies)
Discussion started by: prpkrk
7 Replies

9. UNIX for Advanced & Expert Users

Unable to install client AIX LPAR to vscsi hdisk provided from VIOS

Hi everybody, I have Power5 server with 4 internal hdisks each of 70Gb. VIOS server was installed via Virtual I/O Server Image Repository on the HMC. HMC release - 7.7.0 VIOS rootvg installed on 2 disk(these disks merged to one storage pool during VIOS install process),and 2 others hdisks... (2 Replies)
Discussion started by: Ravil Khalilov
2 Replies

10. UNIX for Beginners Questions & Answers

Hmc lpar console integration

We want to integrate powervm by using openstack with hmc. Now we encounter problem with the console, we can open the terminal within hmc, and I think hmc using tech java applet. sample applet code like <applet codebase="https://172.16.28.174/hmc/"... (0 Replies)
Discussion started by: eagle
0 Replies
raidctl(1M)						  System Administration Commands					       raidctl(1M)

NAME
raidctl - RAID hardware utility SYNOPSIS
raidctl -c disk1 disk2 raidctl -d disk1 raidctl [-f] -F filename controller... raidctl -l [controller...] DESCRIPTION
The raidctl utility creates, deletes, or displays RAID volumes of the LSI1030 HW Raid controllers that include RAID support. The utility also updates firmware/fcode/BIOS for both RAID and non-RAID controllers. The raidctl utility requires privileges that are controlled by the underlying file-system permissions. Only privileged users can manipulate the RAID system configuration. If a non-privileged user attempts to create or delete a RAID volume, the command fails with EPERM. Without options, raidctl displays the current RAID configuration on all exisiting controllers. OPTIONS
The following options are supported: -c disk1 disk2 (for on board) Create a mirror using disk1 and disk2. Replace the contents of disk2 with the contents of disk1. Specify disk1 and disk2 in canonical form, for example, c0t0d0. When you create a a RAID volume, the RAID volume assumes the identity of the first target in the disk pair (disk1). The second target (disk2) disappears from the system. Therefore, the RAID volume appears as one disk. To have a successful RAID creation, there must not already be a RAID configuration present on the specified controller. Additionally, the secondary disk must not be mounted, as it has all its data erased and replaced with the primary disk's data. -d disk1 (for on board) Delete the RAID volume specified as disk1. Specify disk1 in canonical form, for example, c0t0d0. -f (for HBA) Force an update. Do not prompt. -F filename controller (for HBA) Update the firmware running on the specified controller (controller). -l [controller ...] (for on board) List the system's RAID configuration. If controller is specified, list RAID configurations for controller. Output from the -l lists the following information: RAID Volume Displays logical RAID volume name. RAID Status Displays RAID status as either RESYNCING (disks are syncing), DEGRADED RAID is operating with reduced functionality), OK (operating optimally), or FAILED (non-functional). RAID Disk Displays RAID disk name. Disk Status Displays disk status as either OK or FAILED. EXAMPLES
Example 1: Creating the RAID Configuration The following command creates the RAID configuration: # raidctl -c c0t0d0 c0t1d0 RAID Volume 'c0t0d0' created Example 2: Displaying the RAID Configuration The following command displays the RAID configuration: # raidctl RAID RAID RAID Disk Volume Status Disk Status ---------------------------------------- c0t0d0 RESYNCING c0t0d0 OK c0t1d0 OK Example 3: Deleting the RAID Configuration The following command deletes the RAID configuration: # raidctl -d c0t0d0 RAID Volume 'c0t0d0' deleted Example 4: Updating Flash Images on the Controller The following command updates flash images on the controller: # raidctl -F lsi1030.fw 0 Update flash image on controller 0? (y/N): y Flash updated successfully EXIT STATUS
The following exit values are returned: 0 Successful completion. 1 Invalid command line input. 2 Request operation failed. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ SEE ALSO
attributes(5) System Administration Guide: Basic Administration SunOS 5.10 17 Aug 2004 raidctl(1M)
All times are GMT -4. The time now is 10:09 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy