finally I've resolved my issue, just by this command:
Frankly I don't understand the importance of this line, although this resolved my problem. so, if someone can explan me its importance, it will help me a lot.
Howto check if a ethernet interface is up?
It's impossible to determine via the ipaddress i have learned, or?
Can someone please give me a hint on howto do?
Environment == Linux x86 GNU GCC.
:D
regards
Esaia (2 Replies)
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Hi All,
I want to configure network into my system.
i tried following in to configure the interface
to find the name of interface
#prtdiag |grep net
i got following
0 PCI-1 33 1 network-SUNW, hme
then i tried following
#prtconf -v |grep net
network, instance #0 (6 Replies)
Hi,
During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured,
what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Hi,
is there any method to check the interface collisions on ethernet NIC in AIX. I know that in Solaris it's netstat -i but I've written that in AIX it doesn't show this.
Thanks®ards,
p (1 Reply)
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Hi ,
Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
LEARN ABOUT MOJAVE
locale::codes::langfam5.18
Locale::Codes::LangFam(3pm) Perl Programmers Reference Guide Locale::Codes::LangFam(3pm)NAME
Locale::Codes::LangFam - standard codes for language extension identification
SYNOPSIS
use Locale::Codes::LangFam;
$lext = code2langfam('apa'); # $lext gets 'Apache languages'
$code = langfam2code('Apache languages'); # $code gets 'apa'
@codes = all_langfam_codes();
@names = all_langfam_names();
DESCRIPTION
The "Locale::Codes::LangFam" module provides access to standard codes used for identifying language families, such as those as defined in
ISO 639-5.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default ISO 639-5
language family codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language families. A code set may be specified using either a name, or a
constant that is automatically exported by this module.
For example, the two are equivalent:
$lext = code2langfam('apa','alpha');
$lext = code2langfam('apa',LOCALE_LANGFAM_ALPHA);
The codesets currently supported are:
alpha
This is the set of three-letter (lowercase) codes from ISO 639-5 such as 'apa' for Apache languages.
This is the default code set.
ROUTINES
code2langfam ( CODE [,CODESET] )
langfam2code ( NAME [,CODESET] )
langfam_code2code ( CODE ,CODESET ,CODESET2 )
all_langfam_codes ( [CODESET] )
all_langfam_names ( [CODESET] )
Locale::Codes::LangFam::rename_langfam ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangFam::add_langfam ( CODE ,NAME [,CODESET] )
Locale::Codes::LangFam::delete_langfam ( CODE [,CODESET] )
Locale::Codes::LangFam::add_langfam_alias ( NAME ,NEW_NAME )
Locale::Codes::LangFam::delete_langfam_alias ( NAME )
Locale::Codes::LangFam::rename_langfam_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangFam::add_langfam_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangFam::delete_langfam_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.loc.gov/standards/iso639-5/id.php
ISO 639-5 .
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2013 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.18.2 2013-11-04 Locale::Codes::LangFam(3pm)