Sponsored Content
Operating Systems Linux Issue with ethernet interface Post 302889543 by cerco on Friday 21st of February 2014 10:25:08 AM
Old 02-21-2014
all ports on the switch are in the same vlan and these ports are working fine. when I try to deconnect hostA from switch and replace it by hostB on the same port, hostB can communicate with hostC (pings are working fine). so i think that the issue come from hostA network config.
I'm pinging IP address and not hostnames

below is the traceroute from A to C:
Code:
[root@sigsrv01 ~]# traceroute 10.6.0.33
traceroute to 10.6.0.33 (10.6.0.33), 30 hops max, 40 byte packets
 1  sigsrv01 (10.6.0.50)  3002.150 ms !H  3002.143 ms !H  3002.133 ms !H
[root@sigsrv01 ~]#

 

10 More Discussions You Might Find Interesting

1. Programming

determine if a ethernet interface is up

Howto check if a ethernet interface is up? It's impossible to determine via the ipaddress i have learned, or? Can someone please give me a hint on howto do? Environment == Linux x86 GNU GCC. :D regards Esaia (2 Replies)
Discussion started by: Esaia
2 Replies

2. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies

3. Solaris

Network Interface Issue

Hi all, Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP. - - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies

4. Solaris

Ethernet card drivers issue...

I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do? Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies

5. Solaris

Network interface issue

Hi All, I want to configure network into my system. i tried following in to configure the interface to find the name of interface #prtdiag |grep net i got following 0 PCI-1 33 1 network-SUNW, hme then i tried following #prtconf -v |grep net network, instance #0 (6 Replies)
Discussion started by: kumarmani
6 Replies

6. Solaris

Sun Solaris ethernet interface

Hi, During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured, what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
Discussion started by: manoj.solaris
6 Replies

7. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

8. AIX

interface collisions on ethernet nic

Hi, is there any method to check the interface collisions on ethernet NIC in AIX. I know that in Solaris it's netstat -i but I've written that in AIX it doesn't show this. Thanks&regards, p (1 Reply)
Discussion started by: pitmod
1 Replies

9. IP Networking

Channel bonding Issue - Bond0 interface not getting up in on RHEL6

Hello, I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Discussion started by: Rohit Bhanot
13 Replies

10. UNIX for Advanced & Expert Users

C program to detect duplicate ip address if any after assigning ip address to ethernet interface

Hi , Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
wnnhosts(4)							   File Formats 						       wnnhosts(4)

NAME
wnnhosts - Wnn6 Kana-Kanji conversion server/dictionary lookup server access control file SYNOPSIS
/etc/lib/locale/ja/wnn/wnnhosts DESCRIPTION
wnnhosts specifies users who can use the Wnn6 Kana-Kanji conversion server (jserver) and the Kana-Kanji conversion server that can be con- nected to the Wnn6 dictionary lookup server (wnnds). The following is the format of the access control file. Place a space character before "{". jserver ja <Kana-Kanji conversion server> { <access control data> : } wnnds ja <dictionary lookup server> { <access data> : } <Kana-Kanji conversion server> is specified in the following format. hostname The Kana-Kanji conversion server that uses the well-known port number(22273) on host hostname. hostname/port_no The Kana-Kanji conversion server that uses port_no as port number on host hostname. <dictionary lookup server> is specified in the following format. hostname The dictionary lookup server that uses the well-known port number(26208) on host hostname. hostname/port_no The dictionary lookup server that uses port_no as port number on host hostname. <access control data> for jserver is specified in the following format. hostname All the users on the host can use data. hostname:username_list username_list contains a list of username separated with ",". Users listed in the list on this host can use data. @username This user can use data from any host. <access control data> for wnnds is specified in the following format. hostname jserver on this host can be connected. jserver and wnnds use the access control information with the host name and port number matched. Lines beginning with ";" are comments. EXAMPLES
Example 1: jserver ja_JP hostA { ;hostC:usr1,usr2,usr3 hostA:usr1,usr4 hostB hostC:usr5 @usrA ;usrB } wnnds ja_JP hostA { hostA hostD } jserver ja_JP hostA/22273 { hostB hostE @usrA } wnnds ja_JP hostA/22385 { hostA hostD } SEE ALSO
jserver(1M), wnnaccess(1M), wnnds(1M) SunOS 5.10 10 Jan 2003 wnnhosts(4)
All times are GMT -4. The time now is 03:01 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy