all ports on the switch are in the same vlan and these ports are working fine. when I try to deconnect hostA from switch and replace it by hostB on the same port, hostB can communicate with hostC (pings are working fine). so i think that the issue come from hostA network config.
I'm pinging IP address and not hostnames
Howto check if a ethernet interface is up?
It's impossible to determine via the ipaddress i have learned, or?
Can someone please give me a hint on howto do?
Environment == Linux x86 GNU GCC.
:D
regards
Esaia (2 Replies)
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Hi All,
I want to configure network into my system.
i tried following in to configure the interface
to find the name of interface
#prtdiag |grep net
i got following
0 PCI-1 33 1 network-SUNW, hme
then i tried following
#prtconf -v |grep net
network, instance #0 (6 Replies)
Hi,
During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured,
what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Hi,
is there any method to check the interface collisions on ethernet NIC in AIX. I know that in Solaris it's netstat -i but I've written that in AIX it doesn't show this.
Thanks®ards,
p (1 Reply)
Hello,
I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Hi ,
Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
LEARN ABOUT DEBIAN
setether
SETETHER(8) System Manager's Manual SETETHER(8)NAME
setether - Set the ethernet address for use with DECnet
SYNOPSIS
setether <if> [<if>...]|all [options]
DESCRIPTION
Set ethernet MAC address on ethernet adaptors
This script should be run at system startup. It will change the ethernet hardware (MAC) address of any or all ethernet interfaces to match
the DECnet node address. DECnet requires that the MAC address of all ethernet adaptors running the protocol be set approriately. If you do
not run setether then you must change the ethernet address in some other way for DECnet to work.
By default no ethernet interfaces will have their MAC addresses changed by setether, if you specify all then all interfaces name eth* will
be changed, otherwise a list of interface names can be specified. setether will enable (UP) all interfaces it changes the MAC addresses
of.
(2.4 only) The first interface specified on the command-line will also be made the default interface for DECnet operations (ie attempts to
contact nodes not in the neighbour table will be done over this interface).
This script must be run with the interface inactive, it is normally run from /etc/init.d/decnet before TCP/IP starts up.
EXAMPLES
set the MAC address of eth0.
# /sbin/setether eth0
set the MAC address of all ethernet interfaces
# /sbin/setether all
HELPFUL HINTS
If you have multiple ethernet cards on your system and they are connected to the the same network you should specify which one you want to
use for DECnet communication on the setether command line, otherwise they will both be given the same MAC address and this is probably not
what you want.
Running DECnet on multiple ethernet interfaces only works under Linux 2.4. If you are running Linux 2.2 then the interface name on the
setether command line must match the one in /etc/decnet.conf(5).
SEE ALSO decnet.conf(5), dntype(1), dndir(1), dndel(1), dnetd(8), dnping(1)DECnet utilities March 01 2001 SETETHER(8)